Question about Scuba Diving & Snorkeling

Open Question

Kawasaki z1000 03

I have a rattleing noise down by the chain and i dont know what it is and suggestions

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6982 Answers

SOURCE: chain rattling noise

Locate the knock sensor on your engine. Quick test on them is to tap on the engine with a small hammer near (not on) the sensor. If engine rpms do not change then likely the sensor is bad. Likely what you are hearing (if it is coming from the engine) is detonation. If the noise is elsewhere, it could be a bad chain in the transfer case, but that would need to be looked at to evaluate the problem further.

Posted on Nov 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Kawasaki GPX 600R there's some noise coming from the cam chain. Someone told me that a few gentle bangs on the tensioner would fix it. Is this true or its better to change the tension


how many miles, if cam chain they are about 80 quid maybe less or more, and this needs to be donwe right mate, or bent valves, it could be tensioner if low miles, so a billet one on ebay. they bolt on at the rear of the engine, low down the barrels external. a billet tensioner is about 50 quid, I might know someone who can make one, he does my suzuki ones, where are you. us uk?

Oct 07, 2014 | Motorcycles

1 Answer

Nasty rattling noise from engine only done 5000 miles


it might be due to loose driving chain or timming chain.
i think your bike is still new so best if you consult the workshop for warranty purpose

May 06, 2011 | 2006 kawasaki ZX-10R

2 Answers

A bit noisey in the left side crankcase area


http://www.bikebandit.com/houseofmotorcycles/2000-kawasaki-motorcycle-vulcan-1500-classic-fi-vn1500n1-us/o/m4398#sch61451

This link takes you to a schematic that shows you your timing system (located on the left side)
worn guides or stretched chains cause a constant metallic rubbing noise while a tapping sound that increases in frequency as you accelerate is usually the sound of a valve needing adjustment (clearance). Hope this link helps. Don't forget to vote.

Nov 28, 2010 | 2000 kawasaki VN 1500 Vulcan Classic...

1 Answer

I own a 2004 BMW R1200CL. Almost every time I crank the engine I can hear the valves rattle. I have checked and adjusted the valve clearances to spec. The rattle goes away after the engine starts, but...


Yep, most of these bikes do rattle on startup. The noise is from cam chain slack. A hydraulic tensioner is used in the engine on each side as there are two cam chains. The tensioner leaks down after the engine sits for a while and the chain rattles for a few seconds till the tensioner gets pumped back full of oil again. Once the chain is tight again, then no noise.

BMW came out with an improved tensioner (doesn't leak down as quickly) that you can install on your engine to fix the rattle. Note that it is much easier to change the RHS tensioner than the LHS one.

Good Luck!

Sep 03, 2010 | 2004 BMW R 1200 CL

2 Answers

My zzr 1100 makes a noise on the cluch side of the motor until it reaches operating temp. whats the problem?


could be valve noise valves should be check at regular intervals a chance it may be a wearing cam chain

Jan 28, 2010 | 1996 kawasaki ZZR 1100

1 Answer

Hi got zxr 600r has just started to rattle but has not lost power pulls good ,the noise is not the bottem end,has no oil leeks did not go bang,


if its on the left side of the motor possible cam chain wearing it will make a rattleing noise have it check out if the chain skips a tooth it could be very costly

Jan 05, 2010 | 1997 kawasaki ZX-6R Ninja

1 Answer

Rattle at 4000 constant reves


from what you describe it sounds like cam chain,use a long screwdriver ( or something like ) as a stethoscope and touch the engine with metal end, put the screwdriver handle to your ear and locate where the noise is coming from ( mind you dont get burned or anthing caught in moving parts )

Oct 09, 2009 | 1989 kawasaki ZXR 400

1 Answer

Engine nose on my 1989 kdx 200 it's like a rattle/tick noise


I suggest doing a compression test. On 2 stroke engines with a symptom of a rattle in the engine, it is usually excessive piston to wall clearance, also known as piston slap. If your compression is low, around 100 psi or less, you should tear down the top end and measure the piston and cylinder for both sizing and clearance.

Sep 23, 2009 | kawasaki KDX 200 Motorcycles

Not finding what you are looking for?
Scuba Diving & Snorkeling Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Scuba Diving & Snorkeling Experts

Bill Boyd

Level 3 Expert

40672 Answers

ray gallant

Level 3 Expert

41407 Answers

Are you a Scuba Diving and Snorkeling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...