Question about Office Equipment & Supplies

1 Answer

Why is my on and off botton stop working tryed putting a new one on but same thing pushing in and out but not turning it on have to do it by wall main

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Expert
  • 1,326 Answers

Odds are the PCB trace on the control panel is broken for the switch from pushing hard on the ON button. You will need to repair the connections or replace the switch or replace the control panel. Good Luck

Posted on Jul 16, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Problem with ac window unit panel and remote will not work,pushed all bottons to work and just wont.Could it be the mother load panel?


Sounds like a control computer board problem. Some times unplugging and leaving it for about 30 seconds and plugging it back in can recover from the fault.

Jun 29, 2014 | Crosley CAE15ESR 15,000 BTU Window Air...

2 Answers

I have a Merlin Powerlift model 430R roller door. The battery went flat in the remote and I replaced it. Now the door will not work via the remote.Works ok from red button on unit. I have tried to reset...


If the LED is flashing rapidly when the button on the remote is not pressed you have interference from something. Check for old remotes stored in a drawer somewhere or some new electric item nearby. Start unplugging things until that rapid flashing stops.

Apr 24, 2011 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

I put a new lamp in last week. on the screen it ask me push enter so i did and the sentence went off the screen and the tv has worked good. now it is asking the same thing and i push enter and the...


reset the TV set, infront of your TV where the LED lights are there is a small reset botton that you can push with the tip of a pencil ot pen hold this botton down for 10-15 seconds then unplug the TV set and let it sit for about a 1 or 2 hours

then turn it back on it should work and if the TV still turns of after a few minutes you might have
a ballast issue sence you already replaced the lamp



PLEASE RATE THIS SOLUTION AS I DO THIS FOR FREE !!!!

Oct 14, 2010 | Mitsubishi WD-52327 52" Rear Projection...

1 Answer

None of the bottons work, tried to cancel but off came on.


Ok, will it allow you to reset the clock? That has to be done before you can use the oven.

May 20, 2010 | Jenn-Air 27 in. Electric Single Wall Oven...

1 Answer

Put in new wall oven , turned on power and set


my kenmore double oven model 41165 has no power....its hardwired 40 amp....it stopped working when it was cooling down after the slf cleaning cycle..we had a storm and had a minute power outage. Finakky got the door open but it wont turn on at all. Tried the breakers but i stll get no power....no even the bulb.......thanks....

Jun 07, 2009 | Ovens

1 Answer

E260 frozen HELP!!!!


ok push the power botton and the play botton at the sametime for a while then it should turn of turn it back and it should be just fine and if it is not try it again hope it helps.

Jul 06, 2007 | SanDisk Sansa e260 MP3 Player

2 Answers

Power button won't shut off


First thing to do is unplug the reciver for 12 to 24 hours. Sounds like it needs to be reset.

Sep 18, 2006 | Denon AVR-1803 Receiver

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

k24674

Level 3 Expert

7993 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...