Question about Minolta Dynax 404Si Film Camera

1 Answer

Battery chamber door menolta 404si

Hi there i`m looking for battery chamber door

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • Minolta Master
  • 102,366 Answers

I believe the 400si battery cover will fit. See http://uscamera.com/2082-0120.htm

Posted on Jul 15, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Can I replace the latch or change the full internal chamber?


sir,
this part is available with Nikon agency, to replace this you have to open the whole camera, then detach the front portion, it doesn't matter, just a piece of rubber or sponge fix on the battery lid, this will be help full to hold the battery at contact perfectly.

Jan 09, 2016 | Nikon 1 J1 Digital Camera

1 Answer

Where is the memory card located?


The memory card slot is near the battery chamber. There is a small slot parallel to the battery chamber. Check the bottom of the camera. There is a door that can be slid outside to open.

Jun 14, 2015 | Canon PowerShot SD500 / IXUS 700 Digital...

1 Answer

APS film chamber stuck shut. Door won't open when film chamber release button is pressed


Sorry to hear about this issue. If you have a change bag, I would put a few jewelers screwdrivers in it then put the camera in it. With the bag closed up I would attempt to forcibly open the back. With the camera in the bag there is not any chance to expose the film. After the film is removed wind it back into the cartridge. Now send it off for developing.

Good luck,
Cordially,

May 03, 2014 | Minolta Vectis S-1 35mm SLR Camera

1 Answer

Can not put back access cover with transmission shafts into transmission chamber


Hi Jose, try twisting the mainshaft back and forth while installing the trap door. Good luck

Mar 30, 2014 | Harley Davidson XL Sportster 883...

1 Answer

Need battery chamber lock for minolta maxxum HTsi plus


I'm assuming you need the whole chamber door. I think it would be pretty hard to find just the door, so I would suggest buying another HTsi Plus just to get the part you need. I looked on Ebay and saw an "HTsi body for parts". It was $30(USD) including shipping, not too bad. If there was a source to purchase just the door, I'm sure it would cost $10-20; so buying another camera body might be a better choice. You could probably buy a decent used/working HTsi for around $60-75. So it is up to you to decide what your best course of action is. If it is the door that you need, they are removed very easily (no tools needed).

Jun 07, 2011 | Minolta Maxxum HTsi Plus 35mm SLR Camera

1 Answer

Stupid question but how do you refill the pepper grinder of the Octo Combo? I don't consider this an appliance since it doesn't use electricity or batteries but couldn't figure out another category for...


Hi, from the photos I see on the web, it looks like you hold the salt chamber and then unscrew the nut on the top of the unit. I would say that you need to then pour out the salt into a small container, and then grasp the bottom (pepper chamber) and pull up on the salt chamber to separate it from the bottom chamber. Fill the pepper chamber and then replace the salt chamber and fill with salt, replace salt cover and then replace nut. I hope this helps.

Jan 02, 2011 | Vacuums

2 Answers

Heater blows cold air


Hi!
If the Temp. Selector Control is set to Heat and blows cold air, your Blend Door Actuator may be stuck or it is inoperative. The actuator is not fixable, if it fails, it must be replaced. Follow the instructions to remove and replace it.
  1. Disconnect battery negative cable from battery and properly isolate to prevent accidental reconnection.
  2. Remove the instrument panel.
  3. Disconnect the electrical connector from the blend door motor/actuator.
  4. Remove the four screws holding the blend door actuator to the plenum.
  5. Remove the temperature blend door actuator.
BLEND DOOR ACTUATOR CONNECTOR e8349ea.jpg

BLEND DOOR FASTENING SCREWS 9744710.jpg

Show your appreciation with a - 4 THUMBS - rating for answering your FREE question. Thank you for using FixYa.

Oct 07, 2010 | 2003 Mercury Grand Marquis

1 Answer

Washing machine door wont open - hotpoint


Hi,
Never reach inside the washing machine with it connected to the mains. The door interlock is always live.
There are several reasons why a Hotpoint door could be jammed shut.
•A broken door catch or door frame where the door catch screws in (they are rubbish on many Hotpoints - always breaking) you can sometimes get the door open if you push the door firmly in as you open it
•If there is water still inside the washing machine, then the door wont open either on these Hotpoint washing machines (not on some others though) If this is the case, when you try to open the door the ****** won't try to move down at all. You can open the door usually if you drain the machine. (only applicable with door interlocks that have a rubber pressure hose attached to them)
•A faulty door interlock
•The pressure chamber can be blocked on some earlier Hotpoint washing machines which gives the same effect as having water in the machine. Basically the washer "thinks" there is water in when there isn't. This would require the washing machine being stripped down to remove and clean the pressure chamber bottle. This cause is only applicable to washing machines where a small rubber hose is connected to the door interlock. This hose allows the door mechanism to be locked and unlocked by air pressure activated by water rising inside the pressure chamber bottle attached at the other end on the tub. Gunge can block the very small aperture where the pressure hose fits to the pressure chamber bottle.
Thanks for contacting fixya.com

Nov 07, 2009 | Hotpoint First Edition FEW12 Front Load...

1 Answer

Battery chamber door


battery doors are sold on Ebay alot cheaply

Dec 22, 2008 | Minolta Maxxum 5 / Dynax 5 35mm SLR Camera

Not finding what you are looking for?
Minolta Dynax 404Si Film Camera Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Minolta Photography Experts

kakima

Level 3 Expert

102366 Answers

Greg Cann
Greg Cann

Level 3 Expert

1114 Answers

TC CAMERA REPAIR.Com...

Level 2 Expert

168 Answers

Are you a Minolta Photography Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...