Question about Radio Communications

1 Answer

Magnum 50 scooter schematic

The wires in the front are cut

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Radio Commun... Master
  • 15,557 Answers

Are they color coded?

Posted on Jul 21, 2013

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Sportster SE. started cutting out last week.Replaced the controller connections right away.Sounds like its shorting out in the headlight assembly. Known problem? Can I get a wiring Diagram?

Hi try this phone number they might b able to help u with a wiring Schematic..02 6921 4444 proprietor Gordon Moore. Email , Cheers

Jan 07, 2017 | Electric Mobility Health & Beauty

1 Answer

Rascal 370 wiring schematic

I can't get the wiring schematic for my Pride scooter either.
For some reason these seem to be proprietary and only available
to their dealers. Try to see if they
can help you.

Aug 30, 2014 | Electric Mobility Rascal Scooter...

2 Answers

Wiring schematic rascal 600 24v electric

hi, firstly what controller is fitted (curtis) ? then i can give you a ideal controller wiring schematic but you won't get hold of a Rascal one..


Aug 16, 2014 | Rascal 600 T Electric Scooter w Seat Lift...

1 Answer

Where can i find the wiring schematics for the ul 370 scooter

I have Spice S-590 when someone call me then his/her mobile shows number busy

Jun 26, 2013 | Health & Beauty

2 Answers

Walkabout 330 mobility scooter wiring problems

I know a motability expert who lives near to me and solves all my problems regarding my motability scooter. His name is Stewart and his phone number is: 07846892398. He may not answer phone but do leave a message because he will always return your call. Hope this is of help. Good Luck

Mar 29, 2017 | Health & Beauty

1 Answer

Disable back-up warning on Drive Phantom Scooter

Most of these units have the back up buzzer shrink-wrapped together in the wiring harness under the rear shroud. aka motor cover. The buzzer is typically between the size of a 25 and 50 cent piece, is black and has two very small wires coming out of it - one red and one black. You can cut one wire where you can reconnect it later - just in case you cut the wrong wire!

Dec 09, 2011 | Drive Medical Phantom 3 Wheel Scooter, Red

1 Answer

My 3 wheeled mobility scooter cuts out almost every time I turn the handle to the left. I think it may have a kinked wire.

This typically happens when the front to rear wiring harness has a damaged internal wire or wires. The front to rear harness runs from the front control console, down through the tiller (T part) through the front wheel frame and angle adjustment collar, and through the bottom frame to the controller. There is a wear area of the wiring at the front bearing of the steering tiller. There are 8 or more wires in a covered jacket that run through this area. Over time they rub and get pinched or kinked and broken. The test for bad wiring is exactly what you describe. Usually the broken internal wiring cannot be seen.
The best solution is to replace the entire front to rear harness with the new connectors at each end. The harness is relatively inexpensive and labor should be about 1 hour. Hope this helps.

Jan 30, 2011 | Electric Mobility 3 Wheel Motorized...

1 Answer

Motor on miter saw is runnig back wards

I would suggest going to and typing in your model number and pulling up a wiring schematic for this tool. If your switch and field are not as shown on this breakdown (its a good one) I would either take it to a repair center or change what is wrong one wire at a time. They also have a toll free number and would be more than willing to help with your problem. Let me know and have a good day. P.S. I would not run the blade backwards though.

Jun 21, 2009 | Milwaukee Tool 10" Magnum Compound Miter...

Not finding what you are looking for?
Radio Communications Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Radio Communications Experts


Level 3 Expert

1654 Answers

Brad Brown

Level 3 Expert

15557 Answers

Mike Charette

Level 3 Expert

1795 Answers

Are you a Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides