Question about Swissvoice Epure Full Eco Cordless Additional Handset - Black

1 Answer

How do I stop the LED flashing - Swissvoice Epure Full Eco Cordless Additional Handset - Black

Posted by Anonymous on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If you subscribe to call waiting from your supplier, be sure to clear all those messages before you attempt the following procedure. The LED is also an indicator for call waiting.

Here is what works for our SwissVoice E-pure phone. When the phone is in the standby mode (waiting for a call), press the UP navigation key on the right side of the phone. These keys are also used for volume adjustment in another mode. This gets you in the missed calls menu. Then press on the down navigation key as often as needed to stop the LED from flashing. By pressing on the down key, you start from the latest missed call and go back.

If the phone has been flashing for some time, you might have to go through a lot of missed calls before they are all cancelled. According to the instruction manual. it can store 50 missed calls.

Good luck.

Posted on Sep 22, 2014

  • Anonymous Apr 26, 2017

    This works thanks, that flashing light was getting annoying.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

PT54DL50


MOST LIKELY problem is the convergence amps but.....
It might be your vertical or horizontal circuit...those initiate a 3 blink failure code too....

Dec 01, 2007 | Panasonic PT-50DL54 50" Rear Projection...

1 Answer

Midland btx2


The red LED on the unit will start flashing when charging begins.

Allow the headset to charge until the unit stops flashing or the blue LED turns on.

When the charge is complete (the red LED is not flashing), release the headset
from the charger

Jul 30, 2012 | Radio Communications

1 Answer

Lt 35 flashing glow plug light


In my case, the flashing glow plug indicator is caused by me replacing the stop lights with LED bulbs. Therefore, a cause for this flashing indication could be a blown stop light lamp. The test for this condition is; while the glow plug indicator is flashing, press and release the break pedal. This should stop the indicator from flashing. Check your stoplights. Or add a load resistor to your LED lamps if you have fitted these.

Jun 01, 2012 | Volkswagen Volkswagen Cars & Trucks

1 Answer

Panasonic projection TV does not turn on.


Power LED flashes orange 1 x 5 secs. = 1 of 3 fans stopped. TEMP LED flashes 1 x 5 secs, = Temperature error. Lamp LED flashes 1 x 5 secs. = lamp ballast error. (check lamp 1st.)
Hope this helps.

Apr 18, 2010 | Televison & Video

1 Answer

Red Priner LED Wont stop flashing


it is problem paper jum.please chack it then solve your problem

Jul 24, 2009 | Brother HL-2040 Laser Printer

1 Answer

Paper led light wont stop flashing


Pull the tray out and make sure the back guide is pushed against the paper. The back guide tends to move easily on these models

Jul 15, 2009 | Brother HL-2040 Laser Printer

1 Answer

My garage door opener stopped working, I hit the reset button and it started working again, the wired remote on the wall works, but my 2 wireless remotes do not work, I have followed directions to...


IS THE LED FLASHING ON THE WALL BUTTON??

IF THE LED IS FLASHING THE LOCK FEATURE HAS BEEN ACTIVATED. PRESS THE LOCK BUTTON ON THE WALL CONTROL AND THE LED SHOULD STOP FLASHING.

NOW YOU CAN REPROGRAM REMOTES AND YOU ARE ALL SET.

Sep 09, 2008 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

Jvc hd61z575 61in. rear projection tv won't come on


ok you have defective power supply in hotside section! maybe they have abnormal oscillation!

 

Oct 11, 2007 | JVC HD-61Z575 61" Rear Projection...

Not finding what you are looking for?
Swissvoice Epure Full Eco Cordless Additional Handset - Black Logo

721 people viewed this question

Ask a Question

Usually answered in minutes!

Top Swissvoice Lands Phones Experts

kakima

Level 3 Expert

102366 Answers

Computer Repairing
Computer Repairing

Level 3 Expert

14641 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Are you a Swissvoice Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...