Question about Kirby Generation 3 Bagged Upright Vacuum

1 Answer

Replace fan blade e77491 - Kirby Generation 3 Bagged Upright Vacuum

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 357 Answers
Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove a stripped fan blade on Kirby ultimate g


I do not know of any screws that would be stripped right at the fan. Here is a walk through on removing and replacing the fan, the shaft needs to be turned counter clockwise.
Kirby Fan Replacement

800-775-6586
GoodVac com

Oct 03, 2014 | Kirby Ultimate G Bagged Upright Vacuum

1 Answer

My Kenmore Progressive Whisper Belt canister vacuum is not "whispering." In fact, it makes excessive noise during operation - much more than the older Kenmore model that it replaced. I have replaced the...


Probably either bearings in the roller brush, a damaged fan blade, or the bearings in the motor. Take the roller brush off completely, and run the VAC without it. If it's much more silent, then the problem is with the bearings in the roller brush. If it's still noisy, then look closely at the fan that produces the suction, if you can. If you see any damaged blades, then you'll have to replace it. If it seems fine, then it's most likely bearings in the main motor that will have to be replaced. The bearings and the fan blade are NOT expensive parts, but the labor at a shop to change the main bearings would be kinda pricey.

Oct 18, 2013 | Kenmore Vacuums

1 Answer

Very poor suction


Make sure ALL the air passageways are not blocked with any hair, dust balls or other material. If they are ALL clear, then it's probably the fan blade that creates the suction is damaged, maybe a blade or two are broken. It is cheap to buy a new fan blade, but taking the machine apart and replacing the blade would be moderately expensive for a repairman. Maybe you can try to do that yourself. If not, always ask for a complete estimate for the repair, and have it written out on paper before you agree to the work.

Oct 18, 2013 | Dyson Vacuums

1 Answer

I have a 18 yr old Admiral DH359 demudifier. When I turn on the dial (switch) it gives a humming noise buy the blade does not rotate. After about a minute or two it shuts off because of condenser over...


The problem with your unit is the fan. The engine behind the blades have gotten spoilt hence its inability to roll the blades. Usually when the engine of a fan is spoilt as a result of the coil the engine still tries to move but due to the bad coil the engine hums but does not come to a start. The fan is meant to be the main component which regulates the temperature of the unit if the fan does not cool the unit then the unit will overheat and go off. Simplest solution is to extract the entire fan plus its engine and get ? replacement for it. If you have the required expertise to open and reassemble the unit you can do this yourself otherwise get an expert to carry it out for you. Hope this solution has been helpful?

Jun 23, 2011 | Vacuums

1 Answer

Fan blade cracked


It needs replaced before it breaks and pieces get into the motor.
Replacement instructions can be found at http://www.ehow.com/how_5534689_replace-fan-kirby-vacuum-cleaner.html.

Jan 03, 2011 | Kirby G4 Bagged Upright Vacuum

1 Answer

Replacing the fan hub on a kirby classic omega 1CB


I resolved the problem .I found a way to hold the armature shaft still while I unscrewed the pulley drive nut ,which must be removed in order to remove the vacuum fan.

> There probably is a special tool somewhere that would fit over the armature ( the metal part that spins on the shaft of the motor inside the stature) to hold it still ,but since it was suspiciously omitted from the rest of the fan blade parts ,I had to fabricate one myself.

>I happen to have three ,steel blade ,broad paint scrappers which were about 2 to 3 inches wide and thin enough so there blades fitted nicely into the groves that run the length of the armature without damaging it, as would be the case with a narrower screw driver blade .

>Bracing the handles of the 3 scrapper blades in a slot that was in the side of the case ,which was probaby its' intented purpose, held the armature shaft still while I unscrewed the fan nut which happened to have a reverse thread.( turns clockwise to loosen) .

>It unscrewed with ease. Problem solved!

Aug 30, 2008 | Kirby Heritage II Vacuum

1 Answer

The fan blades under the motor are broken i like my dirt devil triangle please help fix it.


http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=758276
Generic problem for all Vacuums
The fan blades under the
Posted by roadrunner19 on Jul 08, 2008
The fan blades under the motor are broken I like my dirt devil triangle please help fix it.

Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. Changing the fan should not be a problem; it happens every so often if you pickup something big and the plastic fan breaks. The cost to repair is about $10.00 to $20.00 plus labor and you can repair it yourself if you are handy or take it to a local vacuum cleaner dealer in your area and they can perform the fan replacement. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.

http://royalvacuums.com/ Customer Service 1-800-321-1134
Hours are: 8:00 AM to 7:00 PM (EST)
Thanks, Don the Vac Man
Go Ahead. Use Us.

Jul 08, 2008 | Vacuums

Not finding what you are looking for?
Kirby Generation 3 Bagged Upright Vacuum Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kirby Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18394 Answers

JoeVacs

Level 2 Expert

357 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1461 Answers

Are you a Kirby Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...