Question about Pool & Spa

Open Question

Jandy Aqualink Firmware Rev B12 Message

I have a Jandy Aqualink 8227. The backllight flashes and the top of the screen says "Firmware Rev B12). The pool filter still comes on at the right time, etc. But obviously, I can't control anything from in the house. Suggestions? Maybe a bad RS/RF Interface board? Just put my house on the market, and I don't want to spend a couple of thousand dollars on a new unit if I can fix this issue. Thanks in advance for your help.

Posted by on

  • Kimin2son Jul 12, 2013


    Thanks for all of the feedback, I will follow through on those. Question - could it be the Wireless Outdoor JBox that communicates between the power center and the wireless remote?

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: jandy one touch control screen

your RS board in the power center is shot. that message means there is no communication to the power center.

Posted on Nov 02, 2008

Ad
CNC65
  • 15 Answers

SOURCE: Jandy Aqualink - Rs, button control red lites on contriol panel

HAVE YOU HAD ANY LIGHTNING STRIKES?

Posted on Nov 06, 2008

PartsCenter
  • 125 Answers

SOURCE: inside control panel displays 6522 rev GG

Aqualink Guide book

Posted on Feb 26, 2009

  • 128 Answers

SOURCE: Jandy Aqualink RS

Disconnect the spa side remote.

Posted on Aug 23, 2009

  • 84 Answers

SOURCE: On Jandy Aqualink RS display it says 6700 Rev C

If you bypass the 4 wire cable wire as described by 'the californ', and the problem persists, there is a problem with the control boards. Either the PowerCenter board or the RS remote board. We see this failure alot. It is usually due to a a problem in the RS4/6/8 electronics but in some cases it is the PowerCenter. They can be repaired at a fraction the cost of new at www.fixyourboard.com. You can send the remote unit first since all the pool functions will remain and they can test it for you. If it is ok, you will have to send the PowerCenter.

Posted on Nov 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have aqualink rs 6 model 8227 we had a power outage for about 5 hours when the power came back on it says firmware rev b 13 and establishing communications but it never does. I can turn everything on...


turn system off then try again make sure wire connecting to controller is plugged in and tight if wireless see if antenna is flashing green and red lights inside of case

Nov 03, 2013 | Jandy AquaLink RS2/6 All Button Dual...

1 Answer

Jandy 8227


make sure 4 pin connector is plugged in and wires arent cut or shorted

May 12, 2013 | Jandy Aqualink Rs4 One Touch Control...

1 Answer

What does firmware rev b13 mean


check wires going to controller and PCB board if ok check wires to see if cut

May 26, 2012 | Jandy Aqualink - Rs24 One Touch Pool / Spa...

1 Answer

I have lost control. Hit the reset button inside the box and now it says "firmware rev B12." But the rest of the screen is blank. help!


From the information given it sounds like it needs to be replaced. On the other hand, a more educated guess might be obtained with a call to the Jandy technical support line at 800-822-7933. They should be able to help you figure this issue out. I hope this helps.

Please vote on this answer. Thank you.

Aug 27, 2011 | Jandy Aqualink - Rs24 One Touch Pool / Spa...

1 Answer

Jandy aqualink says Firmware Rev B11?


my pool power is on but the remote in the house does not work.
firmware rev b-11 is showing on the display and the display lights up.
what could be the problem?

Apr 11, 2010 | Jandy Aqualink Rs4 One Touch Control...

1 Answer

Jandy one touch control screen


your RS board in the power center is shot. that message means there is no communication to the power center.

Sep 13, 2008 | Jandy Aqualink - Rs24 One Touch Pool / Spa...

Not finding what you are looking for?
Pool & Spa Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pool & Spa Experts

Jay Finke
Jay Finke

Level 3 Expert

1339 Answers

Bill Jordan

Level 2 Expert

372 Answers

David Spradling
David Spradling

Level 3 Expert

5045 Answers

Are you a Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...