Question about Raymarine C80 GPS Receiver

2 Answers

Radar screen shows "no scanner". Would like resistance data for cable pin-out from display to scanner head.

Posted by on


2 Answers

Some cable test stuff
Remove the cable from the display, leave the dome connected
I thought the cable end had pin numbers but let me know if it doesn't,
the video pins are 1 and 2 which are located
either side of the key slot
Video pins 1 & 2 resistance 46 Kohms colors 1 white signal, 2
black return
Azimuth 12 &13 resistance 10 Kohms colors 12 purple azimuth +
, 13 grey azimuth -
Trigger 4 & 7 resistance 10 Kohms colors 4 orange trigger
+ ,7 yellow trigger -
Data I/O 6 & 10 resistance 160 Kohms colors 6 green data + , 10
blue data -
Approx. +/- 5 ohms tolerance.
Below is a pin chart of the display connector
2 1
5 4 3
8 7 6
11 10 9
13 12
Other pins on display connector
Battery - pins 3 & 5 both black
Battery + pins 9 & 11 both red
Shield pin 8
Dome connections
Video pin 8 white
Video rtn pin 7 black
Trigger + pin 6 orange
Trigger - pin 5 yellow
Data + pin 4 green
Data- pin 3 blue
Azimuth+ pin 2 purple
Azimuth - pin 1 grey
Battery + red
Battery - Black
There was a note that some cables only have one set of battery
connections pins 5 & 9
Battery connections on 3 & 11 not present on all cables. You should
have the doubled power wires with the 4KW unit.
If the test results did not have the correct ohms then they said to
check it at the dome
If the dome checked ok, then the cable was bad, and to continuity check
the cable to confirm
a bad cable

Posted on Aug 24, 2008

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 20 times.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 16 Answers

Hello Clifford,

This is an old message. Are you still having trouble with this or has it been resolved?

Posted on Dec 28, 2007


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

NMEA Output from Furuno 6" LCD Radar, Model 1623

No it does not output any type of radar video data.

Apr 27, 2010 | Furuno 1623 Radar 16nm Range

1 Answer

JRC 1000 MKII bearing pulse error on receiver screen. Connections to scanner good and scanner turning. How can I determine if the problem is in the receiver? How can I fix it? louonboard

Normally the bearing pulse comes from the bearing pulse generator built inside the motor. Every time the motor turns it sends a pulse down the line showing the radar that it is indeed spinning. There is also a Heading pulse that comes from an electric eye elsewhere in the housing. The other thing could be that the wire carrying the bearing pulse is not getting back to the display. More so than often, it's the motor. I would have the display sent out to be checked on a simulator if there is a marine electronicshop nearby.

Oct 27, 2009 | JRC 1000 MKII Radar GPS Receiver

1 Answer

No radar target images

Sounds like your video cable inside your radar cable. Also brings your Gain back to zero, STC back to Zero and rain back to zero. Next increase your gain until you see a picture. If none of that is working, check your cable then finally call a dealer.

Oct 15, 2009 | Furuno 1715 Radar 24nm Range

1 Answer

Hi, I have a Radar Screen. Furuno 1942 MK2 . What Radar Dome can i plug this into. I have a Furuno 1720 Dome

A 1942 is a 6 kw radar a 1720 is either a 1.5 or 2.2 kw dome. The two will not work together. Besides the cabling is different. Also the radar cable on a 1942 is round where as the 1720 is square. The 1942 display should work fine on a 1943 navnet radar.

Sep 24, 2009 | Furuno 1942 Mk2 Radar

1 Answer

C120 displays NO DATA SOURCE in the radar section of the screen. ohns resistance test checked out. what else can it be?

1. you must have the latest software 4.29 the new scanner dont work with the old Software.
2. Be shure that you have really put in the connector of the cable inside the plotter its not so easy.
try the plotter on an nother boat with an working system than you will know if its a problem with the antena or Plotter

Aug 06, 2009 | Raymarine C80 GPS Receiver

1 Answer

Furuno 1715 Radar - 'NO HEADING PULSE'

More than likely the belt has come off again. This is a common problem with this radar. You'll need a small allen wrench to tighten it up again.

Jul 02, 2009 | Furuno 1715 LCD Radar System GPS Receiver

1 Answer

Radar Displays the image upside down

If this is on the radar screen, you'll have to set your heading alignment on your radar. The radar may be 180 degrees out. if this occurs on the plotter, then if you have a heading sensor attached or an autopilot, your heading may be off.

Feb 03, 2009 | Furuno NavNet vx2 GP1720C GPS Receiver

1 Answer

1621 radar will not show target

Could be the video wires in the radar cable

Jan 04, 2009 | Boating

1 Answer

Furuno 1622 doesn't work, water coming out cable at screen!

yes the cable should be replaced if you are lucky, the unit is still OK (display) Try the new cable, draped across the boat before rigging. If fault exists with new cable, replace system, or find a new display on ebay

Nov 17, 2008 | Furuno 1715 LCD Radar System GPS Receiver

2 Answers

Furuno 1623 Radar reading "no heading pulse"

The messages “NO HEADING PULSE” and “NO BEARING PULSE” means that the display is not communicating with the scanner (antenna). Both of these signals are generated in the scanner if you get this error check that the antenna cable is firmly connected and that the contacts are clean and corrosion free.

If the connection at the display looks good and feels like it’s properly connected, check the cable for any damage If you find damage you could try to repair the wires BUT (because of corrosion and moisture problems) IT IS STRONGLY REMENDED that the cable be replaced, but it’s kind of expensive $275.00.

The Part number is 000-130-034. Depending on the marine shops in your area they may have it in stock (or they can order one) but you can get it directly from Furuno at;

I hope it’s just a loose connection. Good luck!

Apr 28, 2008 | Furuno 1715 LCD Radar System GPS Receiver

Not finding what you are looking for?
Raymarine C80 GPS Receiver Logo

Related Topics:

583 people viewed this question

Ask a Question

Usually answered in minutes!

Top Raymarine GPS Experts

Shehu Pro
Shehu Pro

Level 3 Expert

1284 Answers


Level 3 Expert

695 Answers

The Knight
The Knight

Level 3 Expert

74999 Answers

Are you a Raymarine GPS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides