Maytag Washer never stops running, goes from 1 cycle to the next

FIXED Maytag Neptune, Timer Problem - ApplianceBlog

www.applianceblog.com/.../23387-Maytag-Neptune-Timer-Problem

Mar 4, 2011 - 8 posts - ‎3 authors
My countdown timer is stuck at the 33-minute level in the "wash cycle", and repeatedlyruns for a 30-40 seconds, then stops, then runs, then ... Maytag Neptune TL Washing Machine stops in spin cycle ...
10 posts
Jul 25, 2013
Maytag Neptune Washer Won't Spin/drain
7 posts
Jul 4, 2013
Neptune TL Washer FAV6800AWW - DC and UC ...
5 posts
Jul 3, 2007
MAYTAG NEPTUNE WASHER CONTROL PANEL ...
8 posts
Jun 29, 2005
More results from www.applianceblog.com

Troubleshooting a Too-Long Wash Cycle - whirlpool washingmachine ...

ask.metafilter.com/233920/Troubleshooting-a-TooLong-Wash-Cycle

Jan 25, 2013 - We have a Whirlpool Duet washing machine (about 2 years old). Thecycle is taking WAY too long to complete. The load that's running now ...

Maytag Neptune washer repair: motor/motor control circuit ...

? 12:10
https://www.youtube.com/watch?v=ITTbDh8CFEU
Dec 11, 2013 - Uploaded by daytonaturbofreak
Maytag Neptune washer motor/motor control circuit board ... my board just fried - is your washer still working? wondering how longthe conversion fix will last. ... Other times it will run a completecycle without any malfunctions.

model number?

It is a timer problem. There are tiny pins inside of the timer and obviously that part of is bad.

sounds like your water level switch is bad OR the small hose that goes from the waterlevel switch to the bottom of the tank has a hole in it.Try replacing this small hose first.you can go to an auto parts store and match it up.it's usually about 3' long and about 1/4" inside diameter and about 99cents a foot.

It sounds like your timer needs to be replaced. The timer runs the washing machine in a pre-determined pattern. It provides the electricity to all of the washing machine components at the correct time and for the correct length of time.

ive fixed lots off washers over the years[15,000 service calls] and was careful while taking parts off if i wasn't fulmilure with that model,but most timers and knobs have a key way so the knob can only go on one way.if thats not true for you, try this.turn the timer shaft till the washer is at the end of the wash cycle.[finished the load,it would be the final spin ,maybe five minutes long.when thats done the timer advances to off]now knowing that thats an off position set on your knob and then manuly turn it to the off position of the next cycle if it wont run you did it. if not you will have to go to the end of that cycle and remove knob and set to next notch in the knob,until you find the sweet spot.hope this helps God bless,tom

if not running over ck to be sure drain is proper height and end of washer drain hose is not too tight in standpipe sound like siphoning after 1st wash and not filling to advance to rinse also be sure washer dring hose is not more than 6-8 in into standpipe

cold water valve screen plugged or bad valve, just check it!

Are you getting cold water to fill ?How is the water pressure?Timer maybe at fault here.

Rick,
Just call service. Next time you buy a washer or dryer do not shop price! If you have the money to buy a good machine, BUY SPEED QUEEN. IT'S A COMMERCIAL WASHER THAT WILL LAST YOU. THEY CAN DO 8 LOADS A WEEK FOR 25 YEARS.
AND THE BEST WARRANTY IN THE INDUSTRY!
CHECK IT OUT! I'M NOT SELLING YOU ANYTHING. SO DO NOT LISTEN TO THE SALES PITCHES!


Neil



If its 10 years old or more don't put money into it!
The new ones are much more energy efficient!


Try these guys,they are good!
A&E Factory Service is nation wide!
1800-905-9505
They are open 7 days 24 hours to make appointments
Neil