Question about Microsoft Presenter 3000 Mouse

1 Answer

Won't advance slides

The first time I used the 3000 it worked just fine. Now I cannot get it to advance slides.Tried new batteries nothing seems to work. laser light works.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 2 Answers

IF IT JUST DOESN'T WORK... (But the laser pointer is still working when in 'presentation' mode) You need to 'Sync' the presenter and the reciever... as follows: Turn the presenter on, and turn it over so you're looking at the back of it. See the button in the middle? Press that button, and the button on the USB reciever stick, simultaneously, while holding the two of them quite close together. Problem should be solved. If you turn it on and the display isn't working, or if the laser pointer doesn't work when in 'presentation' mode, you need to change the batteries. I thought I had a dud unit until I found out about the 'Sync' function!!! Definitely on the 'need to add to documentation' list!

Posted on Aug 21, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I tried to start my car this morning. There was no electricity at all and i mean at all, The power locks won't even work nothing. The car won't start, it's perfectly silent when you turn


You would need to use a meter or test light to find out what exactly is dead. It could be a short in the fuse box, or a bad connection in the harness, or at the battery or starter.
You may need a repair book or shop manual to get the wiring diagrams.
If nothing on the truck works, you would start at the battery cables and work back to the key switch.

Mar 03, 2013 | 2001 Mazda Tribute

1 Answer

I have a 1999 subaru forester, it can not start today. The car is auto, 110k miles, awd. In the morning, I tried to start it several times, I can only hear click sounds, but engine did not respond. The...


You have a dead battery.
The procedure to fix it is as follows:
1) Charge battery.
2) check alternator belt tension. If loose, tighten or replace.
3) If still no start, replace battery.

Apr 17, 2017 | 1999 Subaru Forester

2 Answers

Slides will not advance.buttons do not seem to work


1. Does the SELECT button work? If so, hold it & remove the tray (if one is present). Skip to step 3.
2. If the SELECT button doesn't work, remove the slide tray (if one is on the projector) using the emergency tray release in the center hub of the projector. 3. 3. Turn the projector on & try to cycle a few times in reverse. This is how you clear a slide change mechanism jam in the projector.
4. If that didn't work, then either you have a broken cycle circuit wire (usually an orange wire within the projector) or the release wire is trapped under the cycle pad. Refer to the following diagram for the correct "at-rest" position of these 2 contacts. (If you don't feel comfortable doing this, then contact a factory-trained repair dealer).
Good Luck !!

jauburn_11.jpg

Feb 15, 2011 | Kodak Carousel 4400 Slide Projector

2 Answers

Microsoft Wireless 3000 Mouse works sporadically (XP)


Turn off all other "wireless" devices (cell-phones, wireless telephones, iPhone) in your home, and see if the light on the receiver is "solid" on.

Sep 13, 2009 | Microsoft Wireless Notebook Optical Mouse...

1 Answer

Slide out quit working and fuse on battery blows everytime I chan


Look under the coach near the slide and look for a pinched or bare wire. Sounds like you have a dead short to ground and could be difficult to find. Check the wiring to the slide motor, could be between the slide switch and the motor. Take a Volt meter and set it to Ohms. With the fuse out check to see if you get an Ohms reading between fuse wire and frame of coach. If you get a reading you have a short. Also check the power wire on the slide motor to motor case. If you get a reading the motor is shoted and needs to be replaced.
Thanks for using Fixya
Jerry

Mar 28, 2009 | Sport & Outdoor - Others

6 Answers

Sony RM-ASP001 for 400 disk changer stopped working


Try the command code switch. I recently had a similar problem when my remote suddenly stopped working. It worked fine one time but nothing the next time I tried it.

I checked the emitter with a digital camera and found it was not working. I did the remote reset (remove batteries and push all the buttons twice, reinsert batteries) and the emitter was now working. However, the remote would still not control the base unit. I did the remote base code reset (push power, volume and TV/DVD buttons together) but this did not help. I then checked the command code switch. This is a small three position slide switch located in the battery compartment on the remote. I slid the switch back and forth several times returning to the default number one setting where it was before. I did not change anything on the base unit but the remote now worked.

Hope this helps.

Dec 23, 2008 | Sony RM-ASP001 Remote Control

1 Answer

Camera powers off when I try to take a picture...


Actually it might be time for a new battery. The symptoms sound as such. Even if the battery is relatively new, it may still be defective. If you have access to a voltmeter, recommend checking the batteries voltage to that printed on its case.

Mar 03, 2008 | Canon PowerShot SD1000 Digital Camera

2 Answers

Microsoft Presenter 3000 does not work


My 3000 has a green light but it only flashes to indicate the sync period during which time you should press the button on the back of the presenter. The presenter works well and to date I have had no problems.

Nov 02, 2007 | Microsoft Presenter 3000 Mouse

Not finding what you are looking for?
Microsoft Presenter 3000 Mouse Logo

Related Topics:

663 people viewed this question

Ask a Question

Usually answered in minutes!

Top Microsoft Computers & Internet Experts

micky dee

Level 3 Expert

2986 Answers

Piyal Perera
Piyal Perera

Level 3 Expert

528 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18424 Answers

Are you a Microsoft Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...