Question about Panasonic PT-51HX41 51" Rear Projection Television

2 Answers

Panasonic PT51HX41E Colors are all messed up

I turned on my TV of 7 years and noticed that i see on the top and bottom of the screen double images of the picture. For example if the top half said the word component I would see it in red and green. I tried using fix the convergent option but nothing I do aligns them up through the remote. Any suggestions - whats the repair going to cost? Is it something I can fix or would need a TV repair guy.

Posted by on

  • wooza Sep 05, 2007

    Thanks for the comments.. Drudd whats service man mode (remote) and just replacing the STK392-110 the only thing needed?

  • wooza Oct 06, 2007

    STK392-110 IC

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Yeah, you could get service to replace convergence IC's and perhaps related resistors for these amplifier circuits, ($250-450);however, if you want save some money do it yourself. Get really familiar with service man mode(remote), invest (if you don't already have) in good small tip soldering iron, solder braid or wick, small gauge rosin core solder(.05), knowledge of resistor color code and a whole lot of patience. I completed this job for less than $100, I purchase two sets STK392-110's because first set was cheap 'knock off' that didn't get me close enough with course service adjustment buy Sanyo. Have fun

Posted on Sep 03, 2007

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 140 Answers

You need to change the convergence ic's IC7001,IC7002 = part# STK392-110. Also check for any burnt or discolored resistors nearby. (about a $350 - $500 repair)

Posted on Aug 20, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Curved double image at bottom of TV and looks like a 3d image


Projection TV2_bing.gif sets have several common problems listed below.

Problem #1) Convergence

Symptoms:

  • Screen Looks 3D
  • Colors wont align
  • Screen may look distorted
  • No Audio/Video - TV2_bing.gif makes a chirping sound.
Problem #2 CRT Fluid has clouded over. Symtoms
  • Dull looking video
  • White looking video
  • Halos around objects
  • Red/Orange looking video

You can see some examples and find a fix here...

bb0cf99.pnghttp://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Mar 03, 2010 | Panasonic PT-53WX53 53" Rear Projection...

1 Answer

Samsung HCN4727W Rear Projection TV, green screen, audio works


These sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the picture to look normal. This is called convergence.

When its out of alignment the video will look 3-D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired. Convergence problems are very common on all Projection TV sets including Sony, Samsung,JVC,Philip Magnavox,Panasonic,Akai2_bing.gif,Pioneer, Hitachi,Mitsubishi,Zenith and others.
You can get more information and a DIY convergenece repair kit with instructions from the link below.

Here are some of the most common problems with these sets...

Problem #1) Convergence

Yours may have one or more of the following symptoms...

*Screen Looks 3-D
*Colors wont align
*Screen may look distorted or warped
*No Audio/Video - TV Shuts down - May also make a constant chirping sound

Problem #2 - Another common problem is dull or washed out video.

Your set may have one or more of the following symptoms....

*Dull looking picture
*White looking picture
*Halos around objects
*Red/Orange looking picture

bb0cf99.pngYou can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Jul 10, 2009 | Samsung HL-R4667W Rear Projection...

1 Answer

I have a Panasonic HDTV Projection PT-47WX42 with double imaging.


Projection TV sets have two very common problems listed below.

Problem #1) Convergence


These sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the picture to look normal. This is called convergence.

When its out of alignment the video will look 3-D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired. Convergence problems are very common on all Projection TV sets including Sony, Samsung,JVC,Philip Magnavox,Panasonic,Akai,Pioneer, Hitachi,Mitsubishi,Zenith and others.
You can get more information and a DIY convergenece repair kit with instructions from the link below.

Here are some of the most common problems with these sets...

*Screen Looks 3-D
*Colors wont align
*Screen may look distorted or warped
*No Audio/Video - TV Shuts down - May also make a constant chirping sound

Problem #2 - Another common problem is dull or washed out video.

Your set may have one or more of the following symptoms....

*Dull looking picture
*White looking picture
*Halos around objects
*Red/Orange looking picture

bb0cf99.pngYou can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Nov 17, 2008 | Panasonic PT-47WX42 47" Rear Projection...

1 Answer

Distortion and double imaging


Projection sets have two very common problems.

The first common problem is convergence


These sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the picture to look normal. This is called convergence.

When its out of alignment the video will look 3-D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired. Convergence problems are very common on all Projection TV sets including Sony, Samsung,JVC,Philip Magnavox,Panasonic,Akai,Pioneer, Hitachi,Mitsubishi,Zenith and others.
You can get more information and a DIY convergenece repair kit with instructions from the link below.

Here are some of the most common problems with these sets...

*Screen Looks 3-D
*Colors wont align
*Screen may look distorted or warped
*No Audio/Video - TV Shuts down - May also make a constant chirping sound

Problem #2 - Another common problem is dull or washed out video.

Your set may have one or more of the following symptoms....

*Dull looking picture
*White looking picture
*Halos around objects
*Red/Orange looking picture

bb0cf99.pngYou can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Sep 07, 2008 | Hitachi 53UDX10B 53" Rear Projection...

1 Answer

Colors and Images


sounds like loose connections on the convergance amps ic's
http://cmpalmer.blogspot.com/2006/11/fixing-my-own-tv-part-ii.html

Dec 25, 2007 | Toshiba 65HX81 65" Rear Projection...

1 Answer

Panasonic 52"problem


You need to change the two convergence IC's - Generic part# STK392-110, Panasonic part# C5AA00000203. You might have problems using the generic #, I would use the Panasonic #

Sep 26, 2007 | Toshiba 46HM95 46" HDTV

Not finding what you are looking for?
Panasonic PT-51HX41 51" Rear Projection Television Logo

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Televison & Video Experts

 Grubhead
Grubhead

Level 3 Expert

5547 Answers

Demonic-2011
Demonic-2011

Level 3 Expert

509 Answers

The Knight
The Knight

Level 3 Expert

75846 Answers

Are you a Panasonic Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...