"S A6" Error shows in the display

You will need to replace the clock/timer control. Here is that part to order. Frigidaire 316557106 Clock timer AppliancePartsPros com

Your range is probably in the Sabbath mode. The error code shown on the display is"Sab", not "5ab".

To disable the Sabbath mode push and hold the Clock pad for 3 seconds.

PF Oven Error Code ShopYourWay

https://www.shopyourway.com/questions/1161483

http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/53991-error-code-pf-oven-not-working.html





A part replacement is suggsted in the links above, but a technician might discover something else, rather than a particular part, as the internet search showed several possibilities.

Error Code: E8 Cause: Control Board Example: Remains in display; oven unusable Corrective Action: Replace control board

f 2 code states that oven has exccded 590 deg w/door in unlocked position or 990 f in locked . either the themp prop is bad or the relay in the EOC ( clock ) is welded closed . I would replace the prob first ( less expensive ) then the clock if needed .. **** ..

Hi,

Equipment is Whirlpool double oven RBD305PDS14 built-in. After a very stormy summer 2007, I thought a power surge may have zapped the control board. Problem initially presented on display as error & fault "E6 F2"; simply pressing "Timer Off" would usually clear this error & fault code.

However, some months later, the display would often go completely blank followed by the beep sequence "short-long-short-short-short" (Morse code: dit dah dit dit dit). No error & fault code would appear. Pressing any keypad oven control did not work at all in this condition. When power was cycled at the breaker panel, the usual "PF" with clock display did not appear.

[TURN OVEN POWER OFF AT BREAKER!!!]

After following the excellent information on "how to remove the control panel" posted in this forum, I first tested the "control panel thermal fuse" (refer to the tech sheet that should be behind the control panel once it is removed). It showed a closed circuit.

I turned my attention to the "flexible" keypad connector cable (error & fault code "E6 F2" is a keypad or keypad connector problem; again, refer to tech sheet). The control panel has a board mounted female connector with two tabs that may be gently pulled upward to release the flexible cable.

I cleaned the flexible cable contact area (it seats into the board mounted female connector) carefully with a Q tip and some isopropyl alcohol. I reinserted the flexible cable and gently pressed down on the two tabs (noted above) on the board mounted female connector. VERY GENTLY tug on the flexible cable to insure it is gripped by the connector.

After all of this monkey business, I re-mounted the control panel display panel on the oven and restored power. So far, so good. After applying power, the "PF" with clock display always appears. I am able to set the clock and press "Start". Over functions normally. The clock displays as normal and I no longer observe the problem I described above.

BTW, I noted the incoming 240V has transient suppression (no surge protection, however

RATE THIS SOLUTION
RNJ VINOD KUMAR

F2-E0 - Shorted Touch Pad (Keypad) - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure.
Select the 'cancel' function and wait 60 seconds.
If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question&&&&

I am quoting above because I really need help. "When I push any of the function buttons on the oven console (Timer, Bake, Broil, Clock) the display shows 0FF in red next to the clock. The oven will not turn on and the timer will not work. I can not find any troubleshooting information on this problem. The oven is a model RDDS30V. Any help would be greatly appreciated!"

My range showed a code of 5A6, I held the clock key down for a few seconds and it corrected itself.