Drills Logo

Related Topics:

Anonymous Posted on Jun 07, 2013

Makita drill corded model 6404 3/8"

Abruptly stopped running, push the button and no movement of drill. Is it likely the cord? Does Makita repair their products?

1 Answer

River bottom

Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

Habit-Forming:

Visited the website for 3 consecutive days.

Governor:

An expert whose answer got voted for 20 times.

  • Expert 174 Answers
  • Posted on Aug 14, 2013
River bottom
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

Habit-Forming:

Visited the website for 3 consecutive days.

Governor:

An expert whose answer got voted for 20 times.

Joined: Jul 20, 2008
Answers
174
Questions
0
Helped
88832
Points
376

You can order a new cord.Go to e replacement parts and put your model number in and this will get you a parts break down

5 Related Answers

Anonymous

  • 1 Answer
  • Posted on Feb 22, 2008

SOURCE: makita 6222D hole drill bit is stuck

When this happened to me I held the shaft of the drill bit tightly with my hand and reversed the direction of drive for an instant. It released at that point. It still does that occassionally though.

Ad

Anonymous

  • 313 Answers
  • Posted on Jun 09, 2008

SOURCE: makita 1420 - 14.4v 1.3Ah cordless drill

try toolpartsdirect.com & go to makita & type in model #

Anonymous

  • 2176 Answers
  • Posted on Feb 11, 2009

SOURCE: wiring diagram for makita 6510 LVR drill

I can't find the wiring schematic online but if you can bear with me I will make some phone calls thurs. and get one faxed to me. It has been so long since I had one apart that I can't remember.

Anonymous

  • 313 Answers
  • Posted on May 29, 2008

SOURCE: makita 650watt corded drill

tap the 3 jaw with hammer not too hard. then the sleeve clockwise

Anonymous

  • 2559 Answers
  • Posted on Jun 04, 2009

SOURCE: I have one makita drill new.but the front part of

Here is a link to the manual page 6 shows how to attach bits

Here is a link to the parts Breakdown

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Replace power cable 8406c

just grab a short extension cord and open up the drill and cut the female end off the extension cord and either solder it in or crimp it in if that seems doable. If it runs in reverse switch the wires.
1helpful
1answer

My Makita 6402 drill stopped working. I press the trigger and it does not make any noise at all

You will need to have someone take it a part and see where the problem lies.
Start with the electrical plug, both the wall plug and inside the drill where the wire attaches to the switch.
Often, the switch is the problem, but the wire itself can be bad, if the cord is worn.
There is such a thing as the wire separating inside the cord.
We will hope the unit is not "toast".
God bless your efforts.
1helpful
1answer

Keeps turning when releasing the power button

Check push button think its faulty which not disconnected the contact instantly
0helpful
1answer

Makita Drill stopped running

Makita will have authorised repair agents that will be able to fix this for you. Or any appliance repair electrician can do the job.
Jun 07, 2013 • Drills
0helpful
1answer

I have a makita drill corded sds and hammer drill, the problem is that it hammers but has stopped rotating

It could be the pin in the lever on the side or a fault in the g/box. You don't say what model it is.
4helpful
1answer

Makita DC1414 schematic

From my experience most chargers do not have replacement parts. And when you do find a schematic for a battery charger it consists of just the cord and housing, and the printed circuit board is not available. This is the case with this model DC1414. The cord and housing are the only things available for replacement. You can purchase a new charger for around $37. If you have any questions please post back.
Oct 11, 2009 • Drills
0helpful
1answer

Makita electric drill

the header lists 2 different tools but if you give me the model number I will find a cord set for you and the wiring diagram that you need. If you also give me the area (US only) I will try and find someone local that has what you need.
0helpful
1answer

Makita 650watt corded drill

tap the 3 jaw with hammer not too hard. then the sleeve clockwise
Not finding what you are looking for?

184 views

Ask a Question

Usually answered in minutes!

Top Drills Experts

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

66963 Answers

john h

Level 3 Expert

29494 Answers

Steve Pack
Steve Pack

Level 3 Expert

7128 Answers

Are you a Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...