Question about Gestetner C7435n Laser Printer

1 Answer

Gestetner c7435 paper jam at fuser unit

Hello, Hope someone can help asap. I have been running, operating, and fixing when needed a Gestetner C7435 for about 2-3 years. Fairly good at figuring things out. Problem: Error remove misfeed at fuser unit.. I have had this error before and fixed the problem. This time however, I have taken out all parts, examined, used a flashlight, removed and checked the fuser unit at least 4 times, rolled the blue dial etc.. The error message is still showing up. My concern is I'm wondering if the memory on the computer is "messed up". In otherwords, there is no paper jam actually. The last thing I printed were whole sheets, no little bit of paper missing etc... Is there a way to reset the Gest. ?? I print off the newsletter for the non-profit organization I'm pres. of Central Florida Palm and Cycad Society. Needs to be printed so I'm losing time this weekend because techs at where we purchased the machine are not in. Thanks for any suggestions. Diana

Posted by on

  • Anonymous Mar 29, 2014

    left paper jam says to open and remove jam. no paper is jam does this dozens of times when coping need help

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 126 Answers

It sounds as if the actuator is out of position or bad. In the fuser exit there should be a thin little black (usually) actuator that hangs down and the paper pushes/ lifts it off of the switch/ sensor as the paper passes. If this is pulled out of its holder or broken it will act like there is still paper jammed. The actuator looks like a little ' j ' and is pressed into its holder. If this is seated properly then the switch is probably bad and needs replaced. About resetting --- a paper jam is considered an 'A' code and does not need the machine to be ' service reset '.
Please let us know what you find out.

Posted on Jan 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Erro code e02 in toshiba estudio 181


hello
dear you have to verify all the exit sensor related
1. do u have look on fuser unit drive gears.
2. is the exit rollers are good some time exit roller got damaged they don't hold hold paper to run out from machine.
3. do u have clean the exit sensor.
4. do you have verify that the exit sensor actuator is free to operate the sensor.
5. some time exit sensor actuator broken.

Aug 28, 2014 | Office Equipment & Supplies

1 Answer

My Gestetner 4532 is not printing a code SC 541.Can someone help me?


That is a bad reading temperature of the Fuser Unit.
I will give same steps to unlock it.
Press yellow key
On the key pad press 1-0-7
Old the red key at least 3 sec
Press copy sp
Exit all the way out
Turn the machine Off / On.
This should be good. If doesn't work you have to call a technician to change some parts of the Fuser Unit like Hot Roller and thermistors.
Hope you understand.

Mar 02, 2011 | Gestetner DSM 651 Copier

1 Answer

Paper jams at fuser unit


did you check the fuser sensore

Dec 16, 2010 | Gestetner DSc428 Color Copier

1 Answer

Paper jam in fuser


Sounds like a timing jam, check paper supply, fanned, good quality, check and clean paper feed rollers.
Registration rollers clean?

If you are a tech, check and clean paper feed clutches, registration clutch. Check fuser for bearings, fuser drive, fuser roller cleaner or worn rollers.
Check exit sensor, is it out of place, is the actuator worn out, is the paper curling and coming off of the paper too early,

Try these, hope it is of some help.
Ed

Apr 23, 2009 | Office Equipment & Supplies

1 Answer

Paper jam 2 - checked every area - cut equipment off and back on - still paper jam 2 - need service person asap.


there are 4 or 5 sensors through paper road:
1)paper input sensor near input roller
2)margin sensor between input roller and cartridge unit
3)transfer bell sensor between cartridge and fuser unit
4)fusing sensor before fusing
5)out put tray sensor
check all sensors if you can find out and check any paper jam there and check sensor stander at normal position, also check each sensor click ok(the micro switch ok) .
there is any sensor out of work should be showing paper jam.

Jan 23, 2009 | Dell 1600n All-In-One Laser Printer

1 Answer

Huge problem!!!!


13.xxx is paper jam error does the paper get picked up? Where does it stop normally the fuser section is to blame or a torn or sticky label in the duplex unit check there.

Sorry for the slow responses been away.
J

Aug 12, 2008 | HP LaserJet 2420dn Printer

Not finding what you are looking for?
Gestetner C7435n Laser Printer Logo

231 people viewed this question

Ask a Question

Usually answered in minutes!

Top Gestetner Office Equipment & Supplies Experts

Adorjani Laszlo

Level 3 Expert

1297 Answers

quennie732

Level 2 Expert

398 Answers

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6674 Answers

Are you a Gestetner Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...