Question about Acer Condre CD-Tracer Pro Tower 7 Drive 52x (C752H1) Burner

1 Answer

One Tray not working

My sith tray isnt working. It just stoped. But all the rest work. It says six ready And wont recognise that theres a blank in the tray. Please Help me. What should I do

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert who has written 50 answers of more than 400 characters.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 158 Answers
Re: One Tray not working

Have you put a cd lens cleaner in the tray do this on all trays to clean lense then if sith tray still dosent accept then replace this one this is all the help can give you. hope you get this one sorted.

Posted on Aug 18, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

My dvd tray is not ejecting,i cannot insert a cd

CD Drive Tray problems
There are two ways to open the CD drive door if the button just below the drive tray does not work.
Go to My Computer and right click on the drive and click on Eject.
If this does not work then you can manually open the CD drive tray by -
Straighten a paper clip and gently insert it into a tiny hole below the drive tray next to the Eject button. Push the paper clip gently until the drive tray pops out, then pull the tray until it is fully out, then you can remove the CD disc.
If you still having problem opening with the Eject button, then the CD drive is faulty and needs replacing.

Feb 05, 2013 | CD & DVD Burners

1 Answer

When I put the disc in to be copies and then the blank discs i press the green start button and it display target drive not ready. How do I get it to copy onto the other discs??

One of the "target" CD-writers is not working -- either the "data" cable is not connected, or the "power" cable is not connected, or the drive itself (either the "spinning" motor, or the "laser") has failed.

Presumably, you don't have to fill "all" the trays, in case you only want to make a few copies of the "source" disk.
So, make a few attempts, with the "source" disk in the "source" drive:
1. put a blank disk into the 1st "target" drive,
leaving the other targets "empty", and press the button.
If it works, then the 1st target drive is OK.
2. put blank disks into the 1st and 2nd "target" drives,
leaving the other targets "empty", and press the button.
If it works, then the 1st and the 2nd target drives are OK.
3. put blank disks into the 1st and 2nd and 3rd "target" drives,
leaving the other targets "empty", and press the button.
If it works, then the 1st and the 2nd and 3rd target drives are OK.

... and so on

If you get a "failure", then you now know which of the "target" drives is the "bad" drive. Either replace that bad drive, or change the cabling inside the unit to "bypass" that bad drive, and put a sticky-label on the face-plate of that drive, saying "do not use this tray".

Oct 16, 2010 | MicroBoards Quick Disc QD-123 (QD-123)...

1 Answer

My DVD-ROM tray opens only after many tries.

As per your information you done all the basic work. Hope you use little bit of oil drop in the side of the tray. If not then try that .If no success then there is a small spring available for tray in and out function. You have to change that spring from a service center or if possible then at home.
Thanks and waiting for your reply.

Feb 04, 2010 | Sony CRX835E CD-RW/DVD-ROM (Combo) Burner

3 Answers

Dvd drive wont open , can hear motor working but drive wont come out. we believe the cd holder isnt shifting up/down to allow the drive to activate & open

Turn the computer off,Remove power cable.Use a peper clip insert it through a hole infront of the dvd drive this will eject the door.Make sure once this is opened the tray is aligned properly,slide it in and out.Push it in all the way then power up the computer.This may work for a while,before it goes again,so you might have to replace it.
Good Luck

Jan 17, 2010 | Lite On SHM-165P6S DVD RW Dual Layer...

1 Answer

Lite on drive drawer is sticking. wont open

Sounds as if you may have a disk in there that's lodged between the tray and the inner mechnism. Use the release pinhole, and a small screwdriver or butter knife to pry open the tray, gently. You'll feel it releasing when you insert a straightened paperclip or other small object.

Oct 25, 2009 | Lite On LH-20A1H DVD RW Dual Layer Burner

1 Answer

Crw4048 tray wont open drive light flashes

power the computer off before you try the paper clip trick

Oct 12, 2009 | CD & DVD Burners

3 Answers

The DVD tray doesnt eject

either it is the ribbon wire, the motor that ejects the tray or the belt that connect the tray and motor is the problem. In case the above three are fine, replace the drive as the sparking might kill your moterboard.

Jul 08, 2009 | Compaq (CDD480172) CD-RW Burner

1 Answer

My acer

How long has it been giving this problem, if its less than a cpl days you can try restoring to a previous date since some viruses ca cause that problem. If that doesnt work or your system isnt infected then i guess your drive is dead and you will need to get a new one... you could also try your drive on another computer, to ensure its dead.. Let me know what happens..

Dec 30, 2007 | Acer (91.42R37.001) CD-RW/DVD-ROM (Combo)...

1 Answer

Drive will not work at all

You may need to disable CD autorun feature. What version of Windows do you have?

Nov 09, 2007 | NEC NR 7900A (NR7900) CD-RW Burner

1 Answer

Device Won't Recognise Blank CD-R Media or Certain Music CDs.

try and see if you can pull a directory using explorer,, sometimes if you record to the full 80 minutes capacity, the disc will return an error,,,even if you recorded it on that drive...also i know this may sound strange but on the drive tray itself take the mount where the laser is mounted and extend it out to the furthest travel point ,,,gently,,,do not force...load the disc, and see if it is now recognized,,,sometimes it is a timing issue, and this way the tray/laser recalibrates itself....

Jul 03, 2007 | LG GSA-2166D DVD RW Dual Layer Burner

Not finding what you are looking for?
CD & DVD Burners Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acer CD & DVD Burners Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Gareth Cockram
Gareth Cockram

Level 3 Expert

657 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Are you an Acer CD and DVD Burner Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides