Question about Gigabyte GA-965G-DS3 Motherboard

2 Answers

Connecting hdd led lead and power led lead,where do they go ?

Ive connected my m/board but not sure where my hdd led lead and power led go on system board

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 6,966 Answers

Hi, There are 3 versions of this motherboard; 1.0, 2.0 & 3.3, but the layout is identical. The general layout is shown in pins.jpg. For the power led, the white wire goes to the (-) terminal either pin 2 or 3, both are MPD- while the green goes to the ( ) or pin 1 (MPD ) as shown in powerled.jpg HDDpins.jpg shows the connection of HDD led, the white goes to pin 3 or HD- while the red goes to pin 1 or the HDD . I cropped these images from the manual which is also available at the gigabyte website. Hope this gives you some ideas and workout of you. Good luck and pls post again how things turn up. Kind regards.

Posted on Aug 15, 2007

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,114 Answers

You can download all the info for this board from the following link: http://www.gigabyte.com.tw/Support/Motherboard/Manual_Model.aspx?ClassValue=Motherboard&ProductID=2361&ProductName=GA-965G-DS3 The front panel & power connectors are just below the IDE connector (see diagram). Connect the power LED on the 3 pin header lust to the left of the front panel headers. Connect the HDD LED to pins 1 & 3 of the header. Please update the question & let us know if the information given was useful to you - Good Luck!

Posted on Aug 15, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiring motherboard to a atx tower


The motherboard manual will give you a breakdown of the cast-to-motherboard connections for the board. They differ slightly from board to board, but the connections are almost always found at the bottom front corner of the motherboard. There will be connections for the hard drive LED, the power LED, the power switch, the reset switch, and on some, the speaker (optional). The power switch and the reset switch connectors , 2-pin plugs, are not polarized, meaning that they can be connected to their pins either way without issue. The Power and HDD LED plugs are polarized, as LEDs have a positive and negative. Get this plug backward and the LED won't work. These are also 2-pin plugs. The power LED usually has a green and white wire (Green is +) and the HDD is usually red and white (Red is +) . Some motherboards have color-coded pins -- DO NOT TRUST THEM IF YOU DON'T HAVE A MANUAL -- they are not always standardized. Some motherboards have small print on the board adjacent to the pins to identify them. You CAN trust these. Otherwise, go to the Motherboard manufacturers site and get the manual for the board. The model number is on the board and can be searched for. If the manufacturer's name is not obvious, Google the model number and it will usually lead you to the manufacturer.

Dec 17, 2011 | Intel Motherboard

2 Answers

Don't have manual and I am not sure how to connect the power switch, reset switch, power LED and HDD LED


if you do not have the manual it's here.

http://www.msi.com/index.php?func=downloaddetail&type=manual&maincat_no=1&prod_no=260

those leads go on pins that are together usually by one edge of the board.They are hard to see but are marked.you should be able to see the reset and power switch quite clearly and if the leads are not lablelled then trace them back to the small reset switch and the power on switch

Jul 06, 2010 | MSI K9VGM-V Motherboard

1 Answer

Power connections for tower led's


The manual in question can be located here

http://download.intel.com/support/motherboards/desktop/sb/d1047103_en.pdf

It is a pdf file, so you will need ADOBE,
I have checked and the pinout for the front panel connectors is there.

May 24, 2009 | Intel D945GTP Motherboard

2 Answers

Can't connect power switch reset switch hdd led to front panel of the mother board can you help me please


If your power is correct, then the reset leads comes to the 2 pins imm. after the power connection...................sodeep

May 16, 2009 | Computers & Internet

1 Answer

KM18G pro motherboard power connection, reset sw, power sw, etc.


Hi.

You can download the manual for your motherboard here.

Inside you will find information of where does each connector go. Each connector on the case has a marking on it (HDD, PWR, RST or similar) which stands for hard disk LED, power button, reset button and so on. Connect it to the right place, and problem is solved.

If you need any further assistance, feel free to ask.

---
Your responses are intended to improve the level of service provided. Please rate your experience.

Jan 18, 2009 | Albatron nForce2 KM18G Pro (KM18G PRO 2.0)...

1 Answer

Motherboard shuts down before booting !


You should clarify this a bit more, but please make sure all of your fans are plugged in and the no jumpers are set to over-clock the processor.Also, double check that everything is fundamentally compatible.

Dec 16, 2008 | Computers & Internet

3 Answers

I have a e-machine. Model w3619 a friend sold to me. He unplugged the two power leads that lead from the power button on the front panel from the motherboard.Where do i reconnect them?


The correct wiring plan for this computer is as follows:

Pwr Led Pwr Sw N/C

X X X X O

X X X X X
HDD Rst N/C

Note : N/C = no connection, top row has no pin, bottom row has a pin but not connected.

when you plug in the Pwr Led and HDD connectors, a light should come on, if it doesn't , turn off the pc and turn the connector round on the pins, re -power on your pc.



Nov 30, 2008 | E-Machines (308714) Motherboard

2 Answers

Reset/power/led etc..lead connections


on most motherboard it is possible to read there to set the wires.
hope this helped a little.

May 15, 2008 | Compaq Presario 5000 PC Desktop

2 Answers

Pwer led,resetsw,hdd led,pwer sw


Hi,
It appears your board is made by Jetway.
Heres your link for the manual:-
http://www.jetway.com.tw/jw/downloadshow.asp?productid=V266B#
You can also download drivers et,c. from the same site.

Please don,t forget to rate the Post.

Best wishes mike @Compurepair

Mar 29, 2008 | Intel Motherboard

2 Answers

MS-6378 ver 2 Motherboard fitted to my Time Computer


here it is your manual man
http://asia.msi.com.tw/index.php?func=downloaddetail&type=manual&maincat_no=1&prod_no=283

msi site your board/the manual..youll have there at the beginning the diagram of wires and pins..
I have a MSI too..great boards man..great boards..
fixya:)
bye

Feb 07, 2008 | MSI MS-6378 Motherboard

Not finding what you are looking for?
Gigabyte GA-965G-DS3 Motherboard Logo

Related Topics:

3,159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Gigabyte Computers & Internet Experts

David
David

Level 3 Expert

781 Answers

Alun Cox

Level 3 Expert

2678 Answers

Gbenga

Level 2 Expert

105 Answers

Are you a Gigabyte Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...