Question about Sony Audio Players & Recorders

Open Question

Rewire headphones How to re cord sony mdr v6

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: ear pad replacement instructions for Sony MDR-V6 Headphones

Hello to all who have exhausted all avenues seeking instructions on how to remove and replace Ear Pads on Sony MDR-V6 Headphones.... All that is required is a little patience maybe some fingernails... The Pads simply slip on and off by pinching ends of cuff that is nearest the plastic backing of The Headphones by pulling them from their seat/flange .. i found it easiest to just roll the cuff off using my thumb w/rolling motion away from the plastic backing/housing of the headphones.. no tools required.. they are installed exactally like one would place a tire on a rim.. exact same motion is required as when removing a tire.. i can give no better illustruction than comparrison to tire removal and replacement. Be careful to make sure one end in completely set deeply into one side before attempting to pull opposing side over its side/flange..start on top and work way around to bottom or vise versa.. To get an idea of what you are attempting to do take a close look at new headphone pad rear and you will see the small flap of leather on rear .. there is a small overlap that fits perfectly over the flange.. dont try to force it as you may tear them...

Posted on Nov 14, 2008

  • 4 Answers

SOURCE: How to Rewire Sony MDR-7506 headphones

Okay, cut and strip the cord. There should be two copper wires and (on Sony headphones, at least) a red and a green strand. On a new 1/8" jack, there should be three connections. The middle one is left, and is where the green one goes. The short one on the side is right, and is where the red one goes. The long bit is the common, and is where the copper one goes. Before you solder, however, remember which strand is which, because you have to sand or burn off the colored enamel. (Use a fine grain paper, or use a standard lighter or stick match- anything else might damage or melt the wire)

Posted on Apr 03, 2009

Grubhead
  • 5047 Answers

SOURCE: sony mdr-v700dj Headphones needs new cord! The

All you need to do is solder a new plug on to the end of the remains of the cable coming out of the headphones, then buy an extension lead. It will be much easier than replacing the entire lead, as getting into headphones is a very tricky thing to do.

Posted on Feb 12, 2010

Grubhead
  • 5047 Answers

SOURCE: How can I replace the cable on Sony MDR-V6 headphones?

http://www.fixya.com/support/r4548519-replacing_dodgy_plug_cable_headphones

Take a look at this Tip of mine, just treat it if the cable was faulty!

Posted on Nov 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am looking for replacement earpads for Sony MDR V600 headphones. Will replacement pads for MDR 7506 fit the V600?


Yes, the replacement pad for mdr 7506 fits in for the v600. They can be replaced for one another. There are different types of v600 and 7506, You just have to look for the 7506 that looks more like the v600. That should do the job for you. Hope this information helped You.

Jan 13, 2011 | Sony MDR-V6 Professional Headphones

1 Answer

Sony mdr-v700dj Headphones needs new cord! The cord was sliced in half in the middle. The headphones are practically brand new. Is there a way to replace the cord?


All you need to do is solder a new plug on to the end of the remains of the cable coming out of the headphones, then buy an extension lead. It will be much easier than replacing the entire lead, as getting into headphones is a very tricky thing to do.

Feb 10, 2010 | Sony MDR-V700DJ Professional Headphones

5 Answers

Ear pad replacement instructions for Sony MDR-V6 Headphones


Hello to all who have exhausted all avenues seeking instructions on how to remove and replace Ear Pads on Sony MDR-V6 Headphones.... All that is required is a little patience maybe some fingernails... The Pads simply slip on and off by pinching ends of cuff that is nearest the plastic backing of The Headphones by pulling them from their seat/flange .. i found it easiest to just roll the cuff off using my thumb w/rolling motion away from the plastic backing/housing of the headphones.. no tools required.. they are installed exactally like one would place a tire on a rim.. exact same motion is required as when removing a tire.. i can give no better illustruction than comparrison to tire removal and replacement. Be careful to make sure one end in completely set deeply into one side before attempting to pull opposing side over its side/flange..start on top and work way around to bottom or vise versa.. To get an idea of what you are attempting to do take a close look at new headphone pad rear and you will see the small flap of leather on rear .. there is a small overlap that fits perfectly over the flange.. dont try to force it as you may tear them...

Nov 12, 2008 | Sony MDR-V6 Professional Headphones

4 Answers

How to Rewire Sony MDR-7506 headphones


Okay, cut and strip the cord. There should be two copper wires and (on Sony headphones, at least) a red and a green strand. On a new 1/8" jack, there should be three connections. The middle one is left, and is where the green one goes. The short one on the side is right, and is where the red one goes. The long bit is the common, and is where the copper one goes. Before you solder, however, remember which strand is which, because you have to sand or burn off the colored enamel. (Use a fine grain paper, or use a standard lighter or stick match- anything else might damage or melt the wire)

Nov 26, 2007 | Sony MDR-7506 Professional Headphones

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Audio Players & Recorders Experts

kakima

Level 3 Expert

102366 Answers

 Grubhead
Grubhead

Level 3 Expert

5047 Answers

The Knight
The Knight

Level 3 Expert

74106 Answers

Are you a Sony Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...