Question about Drills

Open Question

My Hilti TE 905 AVR would not start

I bought a Hilti TE 905-AVR in 2007, it is not much used, in good condition. I used it two months ago without problem, did some trenching. The serial number is 01-0306132-EJ-07 Now it won't start, both lights at the back are not on. I talked to the HILTI support, in San Francisco, they wanted to have $650 for the service. I needed some tips of diagnose, any help is welcome.

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: i need wiring schematics for hilti te 905 avr

Wiring schematics can be found by Hilti 1-800 number but they probally will not help you. The 905 is programed to shut down for service every 40 hours plus 10 warning. Then in my case I am stuck with a 200 dollar bill to send the tool from Winnipeg to Montreal for reprograming. Its a joke in my situation and its on me from Hilti, what a good name but what a scam.

Posted on Jun 09, 2009

Ad
smjdragonfly
  • 79 Answers

SOURCE: Hilti 905 avr starts up slow and uneven speed.

Some of them typically to start up slow. Less wear on the motor. Also make sure you're not using too much drop cord. No more than 100 ft 12/3. May be the brushes if you've had it for awhile. Please rate me

Posted on Jun 18, 2009

  • 61 Answers

SOURCE: I have a Hilti TE 905 AVR the service light came

If you have the old type TE905, which is the one with the square type handle at the back, the service light will come on for 2 reasons. Either there is a tight bearing which will increase the amount of current used to work the machine. Or more common the carbon brushes need replacing. To reset the light, simply cure the problem.

If you have the newer type TE905 with the large “D” Type handle at the back. It gets a bit more complicated. The service light will come on for the same reasons as mentioned above, but it will also come on after 200 hours of use. It will continue to work for another 50 hours with the light on, then it will shut down completely. This is to ensure that it gets regular service. Once serviced or repaired, it will require resetting. To do this you with need a Hilti optical interface, a PC, and Hilti ODA Software. This is not available to the general public. If your Hilti is less Than 2 years old, call Hilti. They will pick it up, repair it, and send it back to you in 3 working days FREE OF CHARGE. If it is older than 2 years there will be a charge for the repairs.
I hope this helped you. Please leave feedback

Posted on Dec 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hilti TE 905 AVR wont hammer


sounds like it needs a rebuild kit. Hilti.com for parts or to contact Hilti to see if you can get parts. It will also have the parts breakdown.

Feb 21, 2014 | Drills

3 Answers

Reset service light on hilti te 706


I have one Hilti Mechie , TE 706 Avr, Now Red Light Only Blinking ,Mechine Not Working

Jun 12, 2012 | Hilti TE 70 Hammer Drill Performance...

2 Answers

Diagram of hilti te1000 avr


You'll have to call Hilti for that. They're very protective of their material. But I think they'll still fax you a schematic.

Nov 17, 2011 | Hilti TE 1000-AVR Demolition Hammer...

1 Answer

Need parts for a TE 905 AVR


If this is a Hilti demolition hammer! You can contact Hilti USA Direct at (800) 879-8000

Jan 11, 2011 | Garden

2 Answers

Hitli te 905 avr. light is on. any idea what it


If you have the old type TE905, which is the one with the square type handle at the back, the service light will come on for 2 reasons. Either there is a tight bearing which will increase the amount of current used to work the machine. Or more common the carbon brushes need replacing. To reset the light, simply cure the problem.

If you have the newer type TE905 with the large “D” Type handle at the back. It gets a bit more complicated. The service light will come on for the same reasons as mentioned above, but it will also come on after 200 hours of use. It will continue to work for another 50 hours with the light on, then it will shut down completely. This is to ensure that it gets regular service. Once serviced or repaired, it will require resetting. To do this you with need a Hilti optical interface, a PC, and Hilti ODA Software. This is not available to the general public. If your Hilti is less Than 2 years old, call Hilti. They will pick it up, repair it, and send it back to you in 3 working days FREE OF CHARGE. If it is older than 2 years there will be a charge for the repairs.
I hope this helped you. Please leave feedback

Jul 16, 2009 | Hilti Hammer Drill Bit, Te Yx 5/8 In. X 13...

2 Answers

I have a Hilti TE 905 AVR the service light came on and it stopped working. Is there a troubleshooting guide to fix and reset this. Also, schematics can be found at:...


If you have the old type TE905, which is the one with the square type handle at the back, the service light will come on for 2 reasons. Either there is a tight bearing which will increase the amount of current used to work the machine. Or more common the carbon brushes need replacing. To reset the light, simply cure the problem.

If you have the newer type TE905 with the large “D” Type handle at the back. It gets a bit more complicated. The service light will come on for the same reasons as mentioned above, but it will also come on after 200 hours of use. It will continue to work for another 50 hours with the light on, then it will shut down completely. This is to ensure that it gets regular service. Once serviced or repaired, it will require resetting. To do this you with need a Hilti optical interface, a PC, and Hilti ODA Software. This is not available to the general public. If your Hilti is less Than 2 years old, call Hilti. They will pick it up, repair it, and send it back to you in 3 working days FREE OF CHARGE. If it is older than 2 years there will be a charge for the repairs.
I hope this helped you. Please leave feedback

Jul 08, 2009 | Hilti Hammer Drill Bit, Te Yx 5/8 In. X 13...

1 Answer

Hilti 905 avr starts up slow and uneven speed.


Some of them typically to start up slow. Less wear on the motor. Also make sure you're not using too much drop cord. No more than 100 ft 12/3. May be the brushes if you've had it for awhile. Please rate me

Mar 26, 2009 | Hilti Hammer Drill Bit, Te Yx 5/8 In. X 13...

1 Answer

I need wiring schematics for hilti te 905 avr


Wiring schematics can be found by Hilti 1-800 number but they probally will not help you. The 905 is programed to shut down for service every 40 hours plus 10 warning. Then in my case I am stuck with a 200 dollar bill to send the tool from Winnipeg to Montreal for reprograming. Its a joke in my situation and its on me from Hilti, what a good name but what a scam.

Mar 14, 2009 | Hilti Hammer Drill Bit, Te Yx 5/8 In. X 13...

Not finding what you are looking for?
Drills Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Drills Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

yadayada
yadayada

Level 3 Expert

76682 Answers

Brad Brown

Level 3 Expert

16037 Answers

Are you a Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...