Question about Jacuzzi Amiga, Soaking Bathtub with Integral Skirt - T715

Open Question

FLO code My J 385 is setting the FLO code, the jets run at both speeds, the heater will work for a little while if power is left off for a large amount of time, but eventually quits and the FLO code comes back on. Drained, refilled, cleaned filters, tried putting water into filter port, dont know what else to try.

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 80 Answers

SOURCE: "Jacuzzi j-400 series" hot tub- F1 code flashes on control panel

There are two things you can check, there is a tranformer that plugs into the main circuit board(usually a four wire plug). Unplug and check pins for good connection and then reconnect There are usually one or two fuses inside the control box mounted on or near the circuit board. Turn off power to spa and pull fuses and check continunity. This is a good start.

Posted on Aug 19, 2009

SOURCE: Refilled my hottub and now there is a

simple fix its one of two things you did not prime the spa when filling it meaning that u just did not lay a hose in the spa then fill it you always need to prime the heater first along with the circ pump if you do not you will get a thing call airlock which is what it sounds like air in the main circulation pump for the heater.Also could be that u removed the filter while you still had the spa running an clogged the circ pump or it could be the flowswitch. Sounds like u might have a sundance spa an if the flo is flashing its either the air lock or your pump went or its clogged if the flo sign is not flashing then its the flowswitch but in that case w/a solid flo nothing would b working. To fix the airlock just shut the power down an take your hose an force water into the intake side of the filter area this is what u should always do 1st when you fill it that how you prime yuor pump an when fillin it all the way it best to fill it through the other end of the filter just put the hose into the filter tube w/the screw on it.IF THATS NOT IT THEN FEEL YOUR CIRC PUMP IT WILL BE THE SMALLEST PUMP IN THE SPA IF U CAN NOT TOUCH IT FOR MORE THEN A FEW SECS. THEN IT WENT ON U OR IT CLOGGED

Posted on Mar 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I installed a new pump motor. It has power, lights are working but jets are not. What wires could be wrong - I don't have clear red, black, white and green wires. The spa is a freeflow passport spa.


there should be a wiring diagram on the side of the motor make sure if you are running 120 volt you changed the shunting on motor or might have hooked up incorrect if no info call a professional

Apr 18, 2014 | Aqua Flo Aquaflo Flo Master Xp2 Spa Pump...

1 Answer

My new flo-master xp2 spa pump will not engage the low speed. The hi speed (jets) works fine but the low speed doesn't engage. I just hear a clicking and nothing comes on.


if you had ice in it and it was powererd up.. you may have burned out the start capacitor or even the start windings..why was it iced up while working on it..it should have been freewheeled by hand before startup..I just got a tub in here.. had to wait 6 days for it to thaw out..(sign of good insulation) we just ran it for the first time yesterday..got some seals to replace and some switches to repair..

Jan 08, 2014 | Aqua Flo Aquaflo Flo Master Xp2 Spa Pump...

2 Answers

Power trips out when jets are switched on


I'm going on somewhat limited information here not knowing if the tub is newly installed or if this is a spa that has been working in the past and just started doing this. It would be helpful to know if this is a recently installed pump as well. That said here are a few things to check.
If it's a new install: Your electrician has more than likely wired the spa incorrectly. Be sure that the spa pack has 220V going into the pack and that the GFCI is wired correctly.
If it's an old spa with a new problem: A lot of times a bad heater element can cause a spa to trip the breaker. If you have a bad element the spa will operate normally for about a minute when you turn the power on, then trip the breaker as soon as the heater kicks in.
If it only trips the breaker when the pump is turned on to high speed, more than likely there is a problem with the wiring of the pump or the relay on the pump itself.

May 04, 2013 | Aqua Flo Aquaflo Flo Master Xp2 Spa Pump...

1 Answer

Switching jets on trips RCD


This is usually an indicator that the high speed on your pump is bad.
Rod
US Parts Center

May 04, 2013 | Aqua Flo Aquaflo Flo Master Xp2 Spa Pump...

1 Answer

Parts


That would likely be FLO... Check to be sure you have good strong water flo at the jets returning to the pool or spa... Check your filter to be sure you have cleaned it properly. A dirty filter will reduce flo and result in the heater not working if the water flow is too low.

There unfortunately a large number of factors to be able to provide much more information without a detailed description of your equipment, the layout, valve positions and condition of the equipment.

Aug 12, 2012 | Jandy Pool & Spa

1 Answer

My flo-Master XP2 06620397-2 has large leak when the jets are turned on. Do I need a new one or can the leak be repaired?


sounds like you need a new seal kit if it is leaking between the plastic pump housing and the motor. this seal kit is a model PS-200 and will run you about $30

US Parts Center

Aug 23, 2011 | Aqua Flo Aquaflo Flo Master Xp2 Spa Pump...

1 Answer

My hot blows the fuse just as soon as I turn it on, I unhock the heater and it still blows the fuse. How long is the motor gauntee for Flo Msater XP2-551521


1 year.

If you disconnect the jet pump plug from the control box can you turn on the service and not blow it again? That would be the easiest way to confirm a motor failure is your problem.

John

Oct 17, 2010 | Aqua Flo Aquaflo Flo Master Xp2 Spa Pump...

1 Answer

I have a artic spa 2003 ,and is flashes a flo coded ,what could i do to fix this problem,im so fustraded with this thing.pumps work ,jets come on but no heat .


A "FLO (w)" indicator means that there is insufficient water flow to trip the pressure switch and allow the heater to come on. Trouble Shooting: Remove the filters and run the spa. If the indicator goes away the filters are clogged, bad. Locate the pressure switch normally threaded into the heater tube. There should be two wires attached. Remove the wires and connect them together to complete the circuit. If the indicator goes away the pressure switch is bad or requires adjustment. Replace / adjust the switch and reconnect the wires. Do not run the spa permanently without it.

Apr 20, 2010 | Pool & Spa

1 Answer

When I turn on the jets at the first setting it brrrr's but does not start. The second setting works fine and when the second cycle is finished the first continues fine. It is just when it first started...


Sounds like you may have a bad start capacitor that is not kicking the motor when it's set to run the low speed. If it just humms, it's usually a capacitor. It can also be the bearings but if it runs quietly normally, then it's probably a start capacitor. Hope this helps.

Nov 01, 2009 | Aqua Flo Aquaflo Flo Master Xp2 Spa Pump...

1 Answer

Rheostat vs. Thermostat Temperature Control


yes, it should work. Just ensure your rheostat will handle up to 1500 watts at reasonable settings. A better approach is a 1500 watt pulse-width modulator circuit that draws little power itself. these are available where power tools are sold (like harborfreight.com and known as speed controllers. I use one for a large air fan in my garage.

Nov 04, 2007 | Presto HeatDish Compact Heater

Not finding what you are looking for?
Jacuzzi Amiga, Soaking Bathtub with Integral Skirt - T715 Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jacuzzi Home Experts

Mike

Level 3 Expert

4336 Answers

john h

Level 3 Expert

12104 Answers

Donni Steen

Level 3 Expert

659 Answers

Are you a Jacuzzi Home Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...