Question about Linksys NSS4000

2 Answers

Password problem i reset my admin password and then i tried to login using my new password but its says access denied.

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert who has written 50 answers of more than 400 characters.


    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 136 Answers
Re: password problem

On older LinkSys routers, the default username is blank and the default password is "admin." On newer Linksys routers, both the default username and the default password are set to "admin." Once you are past the login screen, you are able to reconfigure the LinkSys router

Posted on Aug 10, 2007

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: password problem - Linksys NSS4000 Network Storage Systems

How can removed my password?

Posted on Mar 06, 2013

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

I have a netgear readyNAS NV+ that i want to reset the password.

Whether you bought a used Netgear router or just forgot your own password, you can reset it and start over.

This is not an unusual problem, so Netgear has made resetting and restarting their routers a simple task

Connect all of your devices.
If your Netgear router is not already connected, it should be plugged in, with one Ethernet cable connecting it to your computer and a second Ethernet cable connecting it to your computer's modem.

Locate the reset button on the rear of your Netgear router.
The reset button is a small inset button and requires a pointed object to reach it.

Use a fine-tipped pen to hold the button down for at least 10 seconds.
The test light should flash during this process.

Open your Internet browser and enter the Netgear router's IP address into the address bar to access the router's information. Generally, Netgear routers use the IP address, but the specific IP address will be listed in the router's manual.

Attempt to log in to the router with the default username and password.
The default username is "admin" and the default password is "password."

If the router's username and password were not cleared away, unplug the router and try holding down the reset button.

While you are holding down the reset button, plug the router back in.
Log in to the router using the default "admin" username and "password" as the password.

You can now reset your information, rename your router and enter your own username and password.

Sep 03, 2013 | NetGear Network Storage Systems

1 Answer

Reset password

Log in to your NETGEAR router by browsing to
Enter the username (admin) and password. By default, the password is password or 1234 unless it has already been changed.
If you cannot log into your router:Unfortunately, there is no way to recover a lost or forgotten password from a router or access point; you will need to reset the device to factory defaults.
however, once the device is reset to factory defaults, you can use the default username ("admin") and password (either "password" or "1234" depending on your router) to reconfigure your router settings.
If it is not visible, you can change your wireless passphrase; however, changing the passphrase will cause you to lose your wireless connection.
Connect your computer to the router with an Ethernet cable before entering a new passphrase into the text box and Clicking Apply.
If there is a small hole in the front or back of the router push a hair pin in to reset to factory settings.

Sep 03, 2013 | NetGear ReadyNAS NV+ RND4000 NAS server...

1 Answer

FTP not working on BlackArmor using IE or Windows 7 Explorer Share created, even public access enabled. Details: 200 Switching to ASCII mode 550 Permission denied

Check on BlackArmor Manager that the FTP mode is enabled for the folder you want access to.
You can check it by typing "" in the adress bar on your explorer, enter your login and password ("admin" and "admin" by default), then click
storage -> shares
if "FTP" is disabled, click on the pen (modify) and enable it. don't forget to click "submit" ;-)

Hope it was helpful

Sep 24, 2011 | Seagate BlackArmor NAS 110...

1 Answer

Need Password to connect i4phone to netgear router

You can know the wep password with below method. Connect your router to computer with ethernet cable then you can access it with following default link. or or or If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. If you are still not able to access router with above ip then you need to RESET it for that press RESET button for 10 seconds it is in back side of router then all settings defaults..Then you can access it with above method. . Then click on wireless->wireless security->WEP security there is code password note down it or enter new password then save setting s and restart router. then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa.

Jan 16, 2011 | IOGear IO GearNASFTP Server Cable DSL...

1 Answer

Lost password to configure network setup, how do I bypass or reset?

For that Connect your router to computer with ethernet cable then you can access it with following default link.

If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it
Still same then you need to reset router for access it with above default ip.
For that press RESET button it is in back side of router press it for 10 seconds then try with above ip..
Then it ask for user name and password.
Type user as "admin" and password as "admin" or "password" or blank.
Then you can see configuration page of router.

Click on wireless settings enable wireless then enable WEP Security then add WEP code .It is your password to connect wi fi.Then save settings and restart router.
Then you can connect your wi fi network with that code.
Let me know if you need further assistance.
Thanks for using FixYa.

Feb 16, 2010 | Linksys EtherFast EFG250 250 GB Network...

1 Answer

Forgot my Login anyway around that?

The best thing to do is to install a bare fun_plug with telnet capability. If you do not know where this is, one version is available at Just follow the instructions in the README file for the latest version.

Restart your DNS-323. Once it starts back up, do the following:

1. Login to your device using telnet. Most OS have this or you can use a free downloadable client like putty
2. You will be faced with a Linux # prompt. From here you can change the password of admin by typing:
# passwd admin
3. After changing the admin password, exit from putty and try logging in to your device via a browser'

You should be able to login using the new password

Please rate our help to keep this free service online

Jan 04, 2010 | D-Link Dns 323 2-Bay Network Storage...

2 Answers

Hi there, I have brand new linksys NSS4000 and i am not able to access the box to do the basic confiigurations, so anybody know the default ip address or how can i access the box?

There are a variety of ways to display the NSS Login window.
•Open the Web browser on your computer: In the Address field, enter "http://NAS<MAC address>" (For example, "http://NAS0018F804E44C".)
•Browse for the NSS from the My Network Places window.
•Select the NSS to a network drive from a mapped network drive.
The NSS Login window appears:

Also please follow the below link for manual it will help you to setup

let me know if this worked for you

Dec 01, 2009 | Linksys NSS4000

2 Answers

I am setting up the D Link DNS 323 but I cannot get6 past the admin password screen. it says in the manual to leave it blank, but this does not work

If it's a brand new out of the box DNS-323 it should be:
Username: admin
Password: <leave blank>

If this is not working, check for CAPS-lock, or perform a reset of the device (see the manual).

Oct 17, 2009 | D-Link DNS-323 (DNS323) Hard Drive Array

1 Answer

D-link DSM-G600 Wireless Enclosure I need the admin password

While running - press and hold the reset button for 10 seconds.
I needed to press firmly before it worked.
You need a paperclip.
Reset button is placed between network and usb connector.

After this you may login with username admin and blank password.

NB! Does not delete any data.

Nov 22, 2008 | D-Link DSM-G600 (DSMG600) Network Storage...

1 Answer

ReadyNAS 1000S

I found this link.

It says that to reset the default admin password you need to reinstall the firmware.

Default DHCP address is

I hope this helps

Dec 19, 2007 | Infrant Technologies ReadyNAS 1000S...

Not finding what you are looking for?
Linksys NSS4000 Logo

Related Topics:

6,338 people viewed this question

Ask a Question

Usually answered in minutes!

Top Linksys Network Storage Systems Experts


Level 3 Expert

413 Answers

Brad Brown

Level 3 Expert

13369 Answers

Daily Mehdi
Daily Mehdi

Level 2 Expert

48 Answers

Are you a Linksys Network Storage System Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides