GO VIDEO TV Problem

A blinking red light on your Sharper Image 7-inch LCD TV usually indicates that there is a problem with the TV's power supply. Here are a few steps you can try to troubleshoot the issue:
1. Check the power source: Make sure the TV is plugged into a working power outlet and that the power cord is securely connected to both the TV and the outlet.
2. Unplug and reset: Turn off the TV and unplug it from the power outlet. Wait for a few minutes, then plug it back in and turn it on again. This will reset the TV and may resolve the issue.
3. Check the batteries in the remote: Make sure the batteries in the remote control are not dead and are installed correctly. If the remote isn't working, it could be the reason the TV is not responding.
4. Contact customer support: If none of these steps work, it may be a hardware issue. Contact Sharper Image customer support for further assistance or take the TV to a qualified technician for repair.
Keep in mind that the exact cause of the blinking red light may vary depending on your specific model of Sharper Image TV, and the manufacturer's troubleshooting steps may differ. It's always a good idea to refer to the user manual or contact customer support for assistance if you're unsure about how to proceed.

Usually fuse near cord interior in case. Teardown. Careful..VOLTAGE danger even unplugged. Touch nothing else.

Blown fuse caused by a shorted power supply. Relacing the power supply board should solve the issue in most cases. You can get a power supply board from www.tvrepairworld.com

Replace the power supply board the blinking power indicator is usually indicating the power supply needs replacement or repair. You can get the replacement power supply boards from www.tvcircuitboards.com

sounds like bad capacitors on the power board. Very common problem. I would look at the caps if any appear even slightly rounded on top they are bad. They should be perfectly flat on top any puffing up means replace that cap.

This is an error code of some fault inside. Kindly call in a qualified service technician.

tried to check first the power supply if no any sign of bulging electrolytic capacitor this was a common that we encountered trouble.

kindly count the blinking led to diagnose where the fault came from..

also try the initial check....open the back cover and inspect the power supply board for any bulged capacitors inside..

this is the only way to get rid of the orange light:

• Connect
• reset
• Blurr
• installation
• trouble
• settings
• service menu
• set
• channel
• parts
• instructions
• troubleshooting
• remote
• connection
• drivers
• blue
• repair
• manual
• bug
• CODES

Problem with Vizio L32 32 in. HDTV LCD Television
how do i turn off the orange light on the vizio tv, it won't go off after the tv is turned off?

Posted by meg_car on Jul 08, 2009

1. 
   

• + Add Clarification Request
• Flag Question

1. 
   

Vizio TV Repair Power supply troubleshooting Picture problem Sound problem

• Service by: mjsazon
  

• 5 Stars
• Email

Solutions (2) Best Solution That little fella is only turned off by unplugging it. If all those little lights in America could be turned off we could do with one less nuclear power plant. If unplugging it is not an option, my wife's solution is to cover it with a piece of black tape.

• 2
• 2

• Answered by Sgt Fluffy Over a year ago
  

+ Add a comment

1. 
   

remove all screws on the back of the tv, carefully pull off back cover. you will see two circuit boards one on the left (Power) and one on the right (Video) on the Video board there is a small plug on the right side with a yellow, white and red wire going into a small white connector. the red wire is what controls the orange light on the front. now that the plug is pulled turn it over and you should see a small white plastic piece that holds each metal connector on the end of the wires in. pry this piece of plastic up for the red wire and pull at the same time, the wire will come out of the connector. now tape the metal connector with electrical tape and tuck it behind something or tape it to the chassis. plug your connector back in. put the rear cover back on. now your tv will only show the vizio logo in white when you have the power on. If you wish to disable the logo for both orange and white just disconnect the white plug completely.

<font size="4"> Please let me know if you got this fixed.Thank You very much!<br /> Tyler<br /></font>