Question about Vacuums

Open Question

I just bought a hyla vacuum cleaner and it won't turn on for the second use. What is wrong?

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Electrolux Z8240 model vacuum cleaner

Inside ,the dust collection container, there at the far end is a white cone shape (another filter). I think you may find this covered in lint etc and if you reach in with your hand you can just pull the stuff off. Happened to me around the two month mark and I THINK, so far, so good. My machine is now not switching off and flashing lights at me and the suction is back to fabulous. Found this information on another obsure website. You would think electrolux would mention it in their "Troubleshooting Guide" GOOD LUCK

Posted on Nov 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove hose from end that goes into vacuum cleaner?


if it is a convulated hose then it is screwed in to the fitting as if it is a left hand thread
the end section in the fitting is normally glued in to the fitting as well, so you will have to use a small flat bladed screw driver and pass it along side of the hose to break the glue
whenyou have the hose out cut off the bad bit or fit the new hose in after you put a small bit of contact cement in the thread of the fitting

Oct 31, 2015 | Hyla NST Vacuum Cleaner NST

2 Answers

Kirby Vacuum Cleaner on/off switch won't stay switched on


If the motor turns on turns off in the course of the vacuuming, check the cord or the switch This is how you replace your cord on a Sentria vaxuum.

Jan 15, 2013 | Kirby Vacuum Cleaner Switch For G3-Sentria...

1 Answer

Kirby ultimate g vacuum cleaner (not the shampooer) leaving white marks/trails all over brown carpet


This is not a normal occurence...maybe something the previous owner did or used the vacuum on?? A KIRBY will not normally leave any marks on Your carpet..
Lee in Australia

Oct 14, 2012 | Kirby Ultimate G Bagged Upright Vacuum

1 Answer

My Miele S3141 canister began acting strange this morning. No suction...so I took off the hose and checked for blockage, (nothing). Now I can't get the hose back on the canister. It just slips ar


see this causes and fix it. God bless you
Air filter:
If the vacuum cleaner won't pick up dirt and has no suction the air filter might be clogged. Remove the filter and either clean or replace it as needed.
Exhaust Filter If the vacuum cleaner won't pick up and has no suction the exhaust filter might be clogged. Remove and clean the filter, replace it if its torn or damaged.


Vacuum Hose If the vacuum cleaner won't pick up and has no suction the vacuum hose might be clogged. Remove the hose from the vacuum cleaner, stretch it out straight, shine a bright flashlight in one end and try to see light through it. If no light can be seen, use something to run through the hose and free up the obstruction.
Vacuum Bag If the vacuum cleaner won't pick up and has no suction the vacuum bag might be full. Clean or replace the bag as recommended by the manufacturer.

Dust Cup AssemblyIf the vacuum cleaner won't pick up and has no suction the dust cup assembly might not be installed tightly, or it might be cracked or broken. The dust cup must seal tightly in order to produce the right amount of suction. If it is cracked or broken, replace it. Most glues and adhesives will not successfully seal the crack.
Blower Wheel If the vacuum cleaner won't pick up and there is no suction, the blower wheel might be jammed or broken. Check the blower wheel to be certain it turns freely. If it doesn't, check to see if there is anything rubbing against it. If not, but it's hard to turn, the motor is most likely the problem.
9_28_2012_11_32_31_am.jpeg9_28_2012_11_32_53_am.jpg

Sep 27, 2012 | Vacuums

1 Answer

Can you wash canister and vortex assembly in Dyson DC17


you need a Hyla they use water as a filter and the smell goes down the drain

Jan 22, 2012 | Dyson DC17 Animal Bagless Upright Cyclonic...

1 Answer

When we use the powerhead of the vacuum and turn the handle to go one way or another the motor sounds like it is going to stop or at least it powers down. what is wrong with it? we have had the vacuum a...


Dear Madam/sir,

While using this type of Vaccum Cleaners we should be little bit careful, why because these Cleaners made not use in harsh but to be used carefully,as you said that you have bought this Cleaner 2 years may be it need a service or the capacity of the vaccum cleaner have been lost due to its interal properties.
my choice is to service it once in two or three months.

Feb 25, 2011 | Filter Queen Majestic Canister Vacuum

1 Answer

Hyla electric brush won't work


Where can I get a Hyla vacuum instruction manual?

Jul 28, 2008 | Vacuums

Not finding what you are looking for?
Vacuums Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vacuums Experts

AskDyson
AskDyson

Level 3 Expert

2572 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18389 Answers

D. Floyd Kolb
D. Floyd Kolb

Level 3 Expert

43501 Answers

Are you a Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...