Question about Staples SPL1201X (CrossCut) Shredder

Open Question

Works on reverse but not on auto - Staples SPL1201X (CrossCut) Shredder

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car will not go into reverse gear. what can cause this problem and how can I fix the problem


if it is an auto transmission run the fault codes and look for a problem reverse servo/solenoid or TCM

Jul 12, 2015 | Cars & Trucks

2 Answers

Why doesn't OfficeMax OM99732 shredder work on Auto?


My shredder would not sense paper being inserted and the sensor could not be cleaned. So "Auto" no longer worked but the manual reverse DID work. I opened the thing up, reversed the polarity on the red and black wires on the connector for the main drive motor and VOILA!!! I can use my shredder in manual mode by switching it to REV. Be mindful that this keeps the motor running until it is switched off. This can heat the motor and cause failure so I limit my shredding to 60 seconds then give it a rest so it will cool down. Also there is no emergency reverse so watch your fingers and neck ties.

Dec 17, 2012 | Office Equipment & Supplies

1 Answer

Shredder doesn't shred.


Shreader wont cut will reverse ok

Dec 17, 2012 | Office Equipment & Supplies

1 Answer

How to check if Auto Reverse Works


Play a tape to the end. If it reverses, it is working properly.

Make sure that you have turned the auto-reverse feature on. The switch is next to the power button.

Jul 13, 2012 | Audio Players & Recorders

1 Answer

95 mustang v6 auto no forward gears but works in reverse had ****** rebuilt and same thing


Maybe your differential is shot and will only allow reverse spin or the transmission was not really rebuilt professionally. Was the transmission checked outside of your car after rebuild? Does your vehicle have a Powertrain Control Module (PCM)? Maybe the module went bad or faulty.

Jun 18, 2012 | Cars & Trucks

1 Answer

Jammed in Auto, but works fine in reverse. How to unjam?


Continue to alternate between auto and reverse a number of times. Try to shred narrower pieces of paper at opposite ends to see if it can trigger the auto trigger wire. All else fails, carefully take the shredding part apart and you may find a hugh paper jam underneath.

Sep 02, 2010 | Aurora Electronics AS662C Shredder

1 Answer

Auto shred not working. Paper had been jammed it it, but I was able to remove it using the reverse option. Reverse works.


revers usually always works, i could be that the paper sensor is not working. there is usually a light beam or other mechanism that senses that paper is in the feed if this is not activated it will not start the motor.

Jan 01, 2010 | Office Equipment & Supplies

1 Answer

1987 porsche 944 auto only works in reverse


sounds like a bad tranny. Gear shifter may be locked, have you checked the tranny fluid?

Aug 02, 2009 | 1986 Porsche 944

1 Answer

Transmission only works in reverse


Sounds like the front auto drive clutch. Will need expert repair or replacment gearbox.

Apr 18, 2009 | 1999 Subaru Legacy

Not finding what you are looking for?
Staples SPL1201X (CrossCut) Shredder Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Staples Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

 Bob Buchholz
Bob Buchholz

Level 2 Expert

136 Answers

ray gallant

Level 3 Expert

41519 Answers

Are you a Staples Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...