Question about Televison & Video

Open Question

Pioneer pro 506pu

Hdmi input ?

Posted by Anonymous on

4 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: I just bought a pioneer elite pro-111fd and i

Make sure your on the correct input that the Cable and PS# are connected to i.e. Input 3, Input 4 etc.

Posted on May 19, 2009

  • 10515 Answers

SOURCE: pioneer 506pu red light is


I am sorry to hear regarding the problem. Disconnect the power supply for few minutes, say 30 minutes and then turn it ON.If you still do not see any picture, than it is an internal failure and needs repair.

There could be few probabilities.What has happened most likely is your Y or Z sustain board has failed and needs to be replaced; both of these are about the same price to have replaced as well. The average cost of replacement for these is $550-$750+ tax, the repair price, however can vary depending on the part of the country you live in and the shop you call out. Sometimes smaller shops that are less dependable will charge less than the large outfits with big overhead costs. If you have electronic repair experience, and test equipment let me know and we can troubleshoot this together, however if you do not a repairman will be required. These sets are fragile and you MUST know what you are doing when repairing them or damage can be caused to them, or you!
This is an unfortunate problem because these televisions should last a lot longer than they do, however the age of them doesn't seem to affect this problem at all. We do warranty work for most of the major manufactures and I cannot tell you how many 1 week old televisions we have done major repairs on. Also the same problem that might have happened to one person's television at 1 week old might have happened to someone else's at 3 years old. These new sets are a shame to be honest with you, nothing is made the way they used to, or the way they should be for that matter. The average span of time for a new plasma or LCD television to last before its first major problem seems to be anywhere less than 3 years.

I am sorry that I do not have a quick fix or easy answer for you on this one, but this set will require board replacement in order to get it running again. Please let me know if there is anything else I can do for you, I will be happy to assist in any way possible.

All of these boards are board level repair,you need to replace the defective board in order to repair the tv set.

I'm not sure about your electronic or tv repair background,but if you have any,and some equipment(multimeter),you could try to fix this yourself.

The Y sustain board is the one to the left from power supply(from the back).

Check any fuse on this board-if any is open=replace the Y sustain.

Same thing for the Z sustain-the one far to the right from the back)

if no open fuse on any of the Y sustain or Z sustain-then some voltage readings will be necessary to diagnose the defective board.

-Vy,is a voltage on Y board-if is too low,disconnect the Y buffer and check again.I voltage comes back up(around-190V,see the exact value on the panel label),then replace the Y buffer.

If still to low,then replace the Y sustain.

It may seem confusing,but these are the steps for a complete diagnose!

There is a least probability of screen being bad. However, the above causes seems to be the main.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Posted on Dec 12, 2010

  • 11800 Answers

SOURCE: I have a Pioneer Elite

The upper Y-drive/buffer board is bad. There's also a good possibility that the Y-SUS board is also bad. Replace the buffer and if the problem isn't fixed replace the Y-SUS board. Here they are

Posted on Sep 05, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a pioneer pro- 506pu tv wont turn on and have red n blue light on the front alternating please help with this issue

Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts.
In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.

Jan 20, 2016 | Pioneer Televison & Video

1 Answer

Pro 435pu

that should find it automatically just turn your computer on and tv and set to hdmi 1 or whatever it should be there shoud no have to set anything up if it is a newer macbook pro or something , goto youtube if this does not work

Mar 28, 2014 | Televison & Video

1 Answer

No image from computer to tv with vga connection

Ensure your TV is turned to computer/VGA input. On your computer use the Windows key + P continuous until it appears on the TV.

Mar 08, 2014 | Pioneer Elite PRO-1140HD 50 in. Plasma...

1 Answer

Pioneer pro 506pu plasma

Connect the dvd playr to the pioneer thx and connect the tv to the pioneer thx.

Dec 15, 2013 | Audio Players & Recorders

2 Answers

My HDMI Terminals for Pro-Ro6u Media Receiver is not working. Do you think it is the terminal or the HDMI Cable.

This could be an HDCP "hand shake" problem. Try turning both the TV and the connecting device off, connect the two using HDMI, turn both of them back on, select the proper input and see if you get a picture. If nothing happens try the other HDMI inputs by following the steps listed above. I hope this helps.

See the following Thread for more information about problems with the Pro-Ro6u.

Feb 08, 2010 | Pioneer Elite PRO-1140HD 50 in. Plasma...

1 Answer

Blue ray lap top to hook up to tv with cable

If your laptp has Blue Ray DVD it likely has an HDMI out jack. Connect this to the HDMI input of you tv. If you TV does not have and HDMI jack but had a DTV jack then get an HDMI to DTV adaptor.

Apr 26, 2009 | Televison & Video

1 Answer

Hook up

The Pro 1000HDI has 1 HDMI input while the pro1000HD does not. Get a good set of component cables and that will upscale to 1080I you'll be fine

Aug 11, 2008 | Pioneer PureVision Pro-1000HD 50 in....

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74106 Answers

Cindy Wells

Level 3 Expert

5100 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides