Question about Audiovox 5BCR07 LCD Alarm Remote Transmitter 5BCR07P

Open Question

Remote LCD not displaying car status

Recently purchased remote 5BCR07P to replace 5BCR03. I was able to program the remote to lock, unlock, open trunk and remote start but the LCD display on the remote does not change nor does the remote make sound. What am I missing? Remote seems to send the signal but not receive the signal back.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Technician can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Technician (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: I bought a car with this starter (below)and no one

I'm not sure about trunk but to start the engine press twice green buttun and engine should start and to shutt it off press green button once.

Posted on Jul 22, 2010

Ad
  • 11 Answers

SOURCE: My top 2 buttons (unlock and lock) came off of my

U COUL GET THE MANUAL ON LINE @AUDIOVOX . COM PURSUIT SERIES MODELPRO- OE4

Posted on Jul 26, 2010

  • 32 Answers

SOURCE: I have Prestige Security Remote Start Car Alarm

where did you get it installed? what kind of car is it? unplug the brain of the security system and see if your car starts

Posted on Sep 12, 2010

richroth
  • 9472 Answers

SOURCE: I have a PR00E4BS 4-button

Here is a link to the programming guide for the remote Here is a link to the manual Here is a link to the installation guide
richroth_11.gif
Happy Holidays

Posted on Dec 12, 2010

  • 1 Answer

SOURCE: I have the ffc id:

http://www.fixya.com/support/t4105172-audiovox_pursuit_pro_keyfob_reprogram

 

Try this link

Posted on Dec 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Astrostart quit working on 03 Impala


The BCM and the key FOB have to be programmed to match by a dealer.

Dec 11, 2017 | Cars & Trucks

Tip

How to Program Acura Remote Transmitter


Acura Remote Alarm / Central locking

Model: CL Year: 2001-2003
Model: TL Year: 1998-2006
Model: MDX Year: 2001-2006
Model: RDX Year: 2007-2009
Model: RL Year: 1996-2004
Model: RSX Year: 2002-2007
Model: TSX Year:2004-2008

System Operation
  • Pressing remote transmitter LOCK button once activates alarm and central locking.
  • Pressing remote transmitter UNLOCK button once deactivates alarm (if fitted) and unlocks driver's door only.
  • Pressing remote transmitter UNLOCK button once also activates driving position memory. Driver's seat and mirrors move into memory position specified on remote transmitter when driver's door opened.
  • Pressing remote transmitter UNLOCK button twice within 5 seconds unlocks all doors.
  • Pressing remote transmitter trunk release button for 2 seconds activates trunk release.
  • Pressing remote transmitter PANIC button for more than 1 second activates panic alarm.
  • Pressing any of the remote transmitter buttons deactivates panic alarm.
  • If vehicle unlocked and doors not opened within 30 seconds, locks are reactivated.
Synchronization.

when
  • Remote transmitter battery replaced.
How
  • Press remote transmitter LOCK button or UNLOCK button 5-6 times.
  • System should now lock and unlock vehicle to indicate synchronization procedure complete.
  • Check operation of remote transmitter
Programming

How
  • Obtain all remote transmitters.
  • Switch ignition ON.
Proceed as follows:
NOTE:Point remote transmitter at central locking signal control module (located behind glove box).
  • Within 4 seconds: Press LOCK button or UNLOCK button of first remote transmitter.
  • Within 4 seconds: Switch ignition OFF.
  • Within 4 seconds: Switch ignition ON.
Repeat procedure above twice.
  • Within 4 seconds: Press LOCK button or UNLOCK button of first remote transmitter.
  • System should now lock and unlock vehicle to indicate programming mode activated.
Within 10 seconds:
  • Press LOCK button or UNLOCK button of first remote transmitter, allowing doors to lock and unlock once.
  • Press LOCK button or UNLOCK button of each remaining remote transmitter to be programmed, allowing doors to lock and unlock once as each remote transmitter is programmed.
  • Switch ignition OFF.
  • Remove key
  • Check operation of all programmed remote transmitters.
Immobilizer

System Operation
  • System arms 5 seconds after switching ignition OFF. Immobilizer warning lamp flashes during this time
  • Switch ignition ON.
  • Immobilizer warning lamp illuminates for 2-3 seconds.
  • If immobilizer warning lamp illuminates for 2-3 seconds then flashes rapidly:
  • Key code not recognized.
  • Remove key and try again.
Programming

When
  • System malfunction.
  • Key added or replaced.
How
Immobilizer can only be programmed using diagnostic equipment.

Model: MDX Year: 2007-2009
Model: TL Year: 2007-2008


System Operation
  • Pressing key LOCK button once locks the vehicle.
  • Pressing key LOCK button twice within 5 seconds activates the alarm.
  • Pressing key UNLOCK button once unlocks the driver's door only and deactivates alarm.
  • Pressing key UNLOCK button within 5 seconds unlocks all doors and tailgate.
  • Pressing key UNLOCK button within 5 seconds and holding will open windows and sunroof
NOTE: Models with "Technology Package": Alarm central locking functions can be altered using digital multifunction display in instrument panel.
  • Pressing key PANIC button for more than 2 second activates panic alarm.
  • Pressing any of the key buttons or turning ignition ON deactivates panic alarm.
  • System will automatically lock all doors when vehicle is driven above 15 mph (if function selected).
  • If vehicle is unlocked and doors or tailgate not opened within 30, 60, or 90 seconds (depending on programming), locks and alarm system are automatically reactivated.
  • Pressing tailgate release button once will open, close or reverse direction of tailgate.
Programming

When
  • Key remote transmitter added or replaced.
  • System malfunction.
How
  • Obtain all keys fitted with remote transmitters.
  • Ensure doors, trunk / tailgate and hood are closed and unlocked.
NOTE: A maximum of 5 remote transmitters can be programmed.
  • Switch ignition ON.
Proceed as follows:
  • Within 4 seconds: Press LOCK button or UNLOCK button of first remote transmitter.
  • Within 4 seconds: Switch ignition OFF.
  • Within 4 seconds: Switch ignition ON.
  • Within 4 seconds: Switch ignition OFF.
Repeat procedure above twice. Locks should cycle when button in pushed.
  • Within 4 seconds of each other press LOCK button or UNLOCK button of each remaining remote transmitter to be programmed, allowing doors to lock and unlock once as each remote transmitter is programmed.
  • Switch ignition OFF.
  • Remove key.
  • Wait 10 seconds.
  • Check operation of all programmed remote transmitters.

Immobilizer

System Operation
  • System arms when vehicle is locked using the remote transmitter.
  • If key code is not recognized:
  • Engine starts, then shuts off.
  • Immobilizer warning lamp flashes once, then blinks until ignition is switched OFF.
  • With ignition switched OFF, immobilizer warning lamp will flash 10 times to indicate the system has reset.
  • Remove key and try again.
Programming

When
  • System malfunction.
  • Key added or replaced.
How

Immobilizer can only be programmed using diagnostic equipment

Model: RL Year: 2005-2009



Programming

When
  • Remote Transmitter added or Replaced.
  • System Malfunction.
How
Remote Transmitters can only be programmed using diagnostic equipment.


Automotive and Commercial Locksmith Acura Remote Transmitter Programming...

on Mar 26, 2015 | Televison & Video

1 Answer

My Toyota Avensis 1.6 2007 the trunk locks automaticly.. when I go to open the trunk it doesn't open,, only if I press Unlock botton on remote! how to fix this?


Battery may be dying in remote and your car should have a setup menu which is accessed through the mileage display. try looking there, also refer to your owners manual if you still have it

Jan 04, 2015 | 2007 Toyota avensis 1.6

2 Answers

Remote control won't lock/unlock doors, but will open the trunk. What;s wrong?


There is a fuse box under the right rear seat cushion behind the driver. In that box is a 10 amp mini fuse marked "TRUNK DR RELEASE". That is the fuse that powers your remote receiver. If that fuse is good, the receiver may have failed. To remove the seat cushion, pull the front of the cushion up and then forward.

Nov 02, 2011 | 2003 Cadillac CTS

1 Answer

I bought a used car toyota camry 2005 and it has avital key less remote system installed. model is 474L. It has remote start working and drive door open/close However, i am not able to open the power...


The Camry you purchased may not be equipped with a power trunk. Press and hold the trunk button for appoximately 4 seconds. The trunk should release if the wire is connected and, you have a power trunk.
The Camry (and other toyotas) require a double pulse on the unlock wire. If the double pulse is not programmed the aftermarket unit will mimic the factory keyless entry. One press of the unlock button opens the drivers door. Immediately press the unlock button again to unlock the other doors.

May 05, 2011 | 474L TX 4-Button Replacement TX Remote

1 Answer

5BCR07P PROGRAMMING INSTRUCTIONS


Ignition on, press and release programming switch three times,you will hear one chirp ( channel1), press lock button on remote, press and release switch 1 time ( two chirps, channel 2) press unlock button, press and release switch 1 time (3 chirps), press green remote start button, press and release switch 1 time ( 4 chirps),press option button. Turn ignition off, test.
After pressing the corresponding buttons on the remote programming sequence above ,you should hear confirming chirps from the alarm.

Sep 29, 2010 | 5BCR07P Remote Replacement Transmitter for...

2 Answers

I need to program a key fob for a 2004 Cadillac CTS. I just purchased the car used. it came with ONE key and nothing els. I have recently purchased a keyless entree remote suitable for the car and was...


Remote Key FOB Information
Transmitter Programming
 1. Close all the vehicle doors.
   2. Insert the ignition key into the ignition lock cylinder.
   3. Press and hold the door unlock switch.
   4. While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
   5. Release the door unlock switch. The doors will lock and unlock to confirm the program mode.
   6. Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
   7. Repeat the previous step to program up to 4 transmitters.
   8. Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter programming mode.
   9. Operate the transmitter functions in order to verify correct system operatio

Sep 17, 2009 | 2004 Cadillac CTS

1 Answer

Remote locks the doors but will not unlock doors or trunk Battery


It is entirely possible that the unlock button on the remote is worn such that it is not making contact. I've seen this happen many times, as the unlock button is pressed so much more than lock. You might try to reprogram the remote first before you look into getting a new remote. The procedure goes like this. Close and lock all doors Key in and out of the ignition 6 times, hazard lights should flash twice Turn key into accessory or on position Unlock and lock doors with drivers switch Press lock or unlock on remote Hazards should flash again to verify recognition turn key off  manually unlock door and then open and shut it.  you should then be able to test remote. 
The key to the procedure is doing step two quickly Hope this helps, if not you may need another remote or see dealer.

Apr 11, 2009 | 2004 Infiniti I35

1 Answer

Recode a key 4 bmw 318i cenral locking


To carry out this procedure you need to have one working key and one key which requires programming. It may help sometimes to hold the key close to the rear view mirror as this is where the sensor is located in most models. 1. With both keys, get in the car and close all windows and doors. 2. Put working key into the ignition and turn to position 1 (the accessories should turn on) (try also position 2) 3. Turn the key back to position 0 and take the key out of the ignition. 4. Using the working key, hold down the unlock button, press the BMW logo (lock button) 3 times, and release the unlock button. Doors should lock and unlock. 5. With the new key, hold down the unlock button and press the BMW logo (lock button) 3 times and let go of the unlock button. Doors should lock and unlock and you're done!! If not working try the following PREPARATION 1. Close all doors, trunk, hood and sunroof. 2. The security system must be in 'disarm' mode. The key must be removed from the ignition key slot. ENTER CODE LEARNING MODE 3. Open trunk and leave it opened. 4. Open the drivers door and sit in the drivers seat. 5. Close the drivers door. 6. Cycle the ignition switch 5 times between the 'OFF' position and position 2,(ignition 'ON', all dash warning lamps will illuminate). The red status LED will illuminate continuously, and the siren will 'chirp' once, to indicate that the code-learning mode has been initiated. ?Do No start the engine.? The Ignition switch cycling in step #6 must be performed within 10 seconds. The sequence in steps #1-#6 must be performed within 45 seconds. REGISTER/DELETE ID CODE(S) 7. Open drivers door, (remain seated in the drivers seat) 8. Close the drivers door. 9. Press and release any button on the remote you wish to register in the system. The status LED will shut off momentarily to indicate that one code has been registered. 10. Repeat steps 7 thru 9 to register the three ID codes. It is possible for the system to memorize a total of 4 different ID codes. As a new code is initialized into the memory, the oldest code is automatically deleted. If you had lost your remotes and wished to delete the lost remote ID codes from the memory, you could initialize the ID codes from a newly purchased replacement transmitter four times thereby deleting the previous ID codes from the system memory. EXITING CODE - LEARNING MODE: 11. Open drivers door, and exit from the vehicle, leaving the door opened. 12. Close trunk. 13. Close drivers door. The LED will turn off and the siren will 'chirp twice. 14. The initialization procedure is now completed; Test all remotes to confirm operation. If this doent work your alarm/central lock needs to be reset

Mar 28, 2009 | 1996 BMW 318

2 Answers

Keys won,t lock or unlock doors


Use this Procedure for Buick Vehicles "With" Driver Information Center Buttons.

This information is in your "Owners Manual" in the "Drivers Information Center Section."

1. Insert Key and turn to ON position so you can access Driver Information Center.

2. Press the vehicle information button until PRESS TO RELEARN REMOTE KEY displays.

3. Press the set/reset button until REMOTE KEY LEARNING ACTIVE displays.

4. Press and hold the lock and unlock buttons on the key-less remote at the same
time for approximately 15 seconds. A chime will sound indicating that the remote is
programmed.

5. To program additional remotes at this time repeat step 4. This vehicle can have a maximum of eight remotes programmed.

6. To exit programming mode turn key off and remove key. Test remote(s).


Use this Procedure for Buick Vehicles "Without" Drivers Information Center Buttons.

To access this display, the vehicle must be in Park (P) with key in the on position (as far as you can go without cranking engine).

1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays.

2. Press and hold the trip odometer reset stem for three seconds. The message REMOTE KEY LEARNING ACTIVE will display

3. Press and hold the lock and unlock buttons on the first key-less remote at the same
time for approximately 15 seconds. A chime will sound indicating that the remote is
programmed.

4. To program additional remotes at this time repeat step 3. This vehicle can have a maximum of eight remotes programmed.

5. To exit programming mode turn key off and remove key. Test remote(s).

Good Luck !

Mar 25, 2009 | 2005 Buick LaCrosse

Not finding what you are looking for?
Audiovox 5BCR07 LCD Alarm Remote Transmitter 5BCR07P Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audiovox Electronics - Others Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Lawrence Oravetz

Level 3 Expert

9845 Answers

Bill Boyd

Level 3 Expert

46703 Answers

Are you an Audiovox Electronics - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...