Question about Minolta bizhub 200 All-In-One Printer

1 Answer

How to solve error code C2351 in konica minolta bizhub 164

Posted by on

  • sandeep shrivastava May 03, 2013

    Now, the malfunction error code is solved by replacing "Fan Motor" of the machine. The Fan was jammed due to which it was not functioning.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Minolta Master
  • 6,161 Answers

Suction fan motor malfunction power off the on wait ten seconds between. check all the vents on the machine remove the covers where they are located and power on the machine check to see if they turn use can air to clean or get them replaced.

Posted on Feb 15, 2015

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

wheatlandsvc
  • 1110 Answers

SOURCE: how to fix error c-1183

This code is for a bin/tray raising or lowering failure in the finisher. This can be caused by either the trays not being fully inserted into the finisher or something stropped the bins from raising or lowering. Check the trays and make sure they are as close to the finisher/fully installed as possible. Then turn off then back on the main power switch (NOT the stand by one on the control panel)
You should see the bins raising and lowering into their home position.

Posted on Aug 03, 2010

herminio_hal
  • 210 Answers

SOURCE: Bizhub Konica Minolta - Error Code C1183

First check the alignment front and rear of the finisher, check the finisher exit guide rollers if the paper is exiting properly, open both rear and the front cover and check the lower gears attach is the up/down drive belt. that lower gear one might be broken by the pin slot.

Posted on Jul 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Erro 2351 da bizhub 164


C2351Suction fan motor malfunction
- The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary.1 Check the connector between FM5-relay CN13-PRCB CN14 for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM5 operation check. 4 Change PRCB.
164

http://printcopy.info/?l=en&mod=erc&brand=Konica-Minolta&model=bizhub%20164&code=C2351

Sep 11, 2016 | Konica Minolta bizhub Office Equipment &...

1 Answer

How to solve konica minolta 164 c2351 problem


Suction Fan motor failure fan located right side of machine from the front. Check vent can air and remove cover check fan and or replace worse case the board that controls it is bad

Dec 21, 2015 | Konica Minolta Office Equipment & Supplies

1 Answer

BIZHUB 164 error M2 what have I to do


Replace the developer and the drum make sure counters are cleared first and that Gradation adj is run along with Toner adj

Jul 10, 2014 | Konica Minolta PAGEPRO 1380MF All-In-One...

1 Answer

BIZHUB 164 error M2 what have I to do


replace the drum and developer and then reset the counter

Jul 10, 2014 | Konica Minolta PAGEPRO 1380MF All-In-One...

1 Answer

How to solve error code C2351 in konica minolta bizhub 164


On a bizhub 165 it's a fault with the sucktion fan motor so check
to see if turning and replace if needed. If this does not fix print control board might need replacing.

Jul 03, 2014 | Minolta bizhub 200 All-In-One Printer

1 Answer

Bizhub 164 error code CC153


Have a tech come and re-flash the firmware, and check the NVRAM. Firmware is only available fro secure Konica Minolta Web site they like to keep they software secure. You mite also have a bad control board. Or the memory on the board, a Tech is required.

May 08, 2014 | Konica Minolta bizhub Office Equipment &...

1 Answer

Sir, My Konica Minolta bizhub 164 shows an error code c3451. How can i solve this problem.


Pressing stop button switch on the machine. It happens due to low voltage or damaged fuser bush.

Feb 13, 2014 | Konica Minolta bizhub Office Equipment &...

1 Answer

Error code c2558 in konica Minolta bizhub 164


help me my konico minolta bizhub 184/164 error (C2558) my mail id ganaa_et24@yahoo.com

Sep 30, 2013 | Office Equipment & Supplies

1 Answer

How to solve error code c2351 in konica-minolta bizhub 164


Suction Fan motor failure fan located right side of machine from the front. Check vent can air and remove cover check fan and or replace worse case the board

Apr 30, 2013 | Konica Minolta bizhub Office Equipment &...

5 Answers

How do I clear error message C-2558 for the Konica Minolta bizhub C253


tis error means abnormal tonder density in the balck image unit take the blacke image unit out and shake it while holding it level and put it back in the machine to reset the error code leave the machine on and open then close the front door

Nov 12, 2009 | Konica Minolta bizhub C250 All-In-One...

Not finding what you are looking for?
Minolta bizhub 200 All-In-One Printer Logo

1,443 people viewed this question

Ask a Question

Usually answered in minutes!

Top Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6161 Answers

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

David Burkhart
David Burkhart

Level 2 Expert

210 Answers

Are you a Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...