Question about Fuji Stabiscope (7512404)

1 Answer

Stableizer not working

Going thru inventory in our office I have come across 2 Fujinon Stabiscope 12 x 40 47. binos. One works the other it seems like the stableizer doesn't work. We are in Anchorage, Alaska and would like to use them on our boat. Is there a way I can fix them or is there somewhere I can get them fixed?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: Stableizer not working

Baker Marine in CA will fix your Stabiscope. They told me $1500 minimum for the same problem. They are the only ones in the Western World that fix these things, truly. I know of a guy in Denmark who was told to send his to Baker. They have no competition nor any canscience!!

Posted on Jul 08, 2012

6 Suggested Answers

  • 24 Answers

SOURCE: Stableizer On or Off

Should be on the left side, near where it mounts on the camera.

Posted on Dec 06, 2007

  • 3 Answers

SOURCE: I have a new olympus

think you need to check what settings your on coz i have the same cam and mine is 100% fine or you may have a folt with the cam

Posted on Jun 25, 2008

  • 686 Answers

SOURCE: drum tilting

post model number please

Posted on Apr 18, 2009

  • 314 Answers

SOURCE: the whole front of my expedition vibrates when i push on the gas

it can be a motor mount. when the vibration occurs shift into N and then if it stops then it is your transmission. it could also be loose lug nuts, a bad wheel bearing, tie rod. or something else in the suspension.

Posted on Jun 10, 2009

  • 1 Answer

SOURCE: Watersystem fault

I've just had my machine fixed by a miele technician. Turns out the rubber beneath the water reservoir had worn out after 5 years. Because it was leaking, the machine was filling up with water. It protects itself by giving you the message. You can remove the reservoir, take a flexible tube/hose and drain the machine. It will probably fix the problem for a while. The Miele part number for the rubberseal is 05046331. Pretty cheap.

Posted on Aug 11, 2009

  • 1 Answer

SOURCE: what would cause a jeep wrangler steering wheel

Check your brakes I had the exact prolem I had the front end aligned ,tires balanced 2 times it finally stopped when I chnged my brake pads

Posted on Oct 16, 2010

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Where do I send a Vivitar product for warranty

Start with

Contact the appropriate office for your country or part of the world and go from there.

May 28, 2014 | Vivitar VIV-CV-1025V - 10 x 25 Digital...

1 Answer

Atn night storm 3 not working

On any tv's pc, any thing that you don't want fried. The powder surge is what kills them powder going on and off buy powder surgers on every thing and you will never have that problem.

May 08, 2014 | ATN Night Vision Night Storm-3 Gen.3...

1 Answer

Only one side of my night vision bino,s are working were can I get them worked on?

Night Owl Optics, El Paso, TX. There is a good possible that one of image intensifier is bad.
ask first what it going to cost, it could be to expensive to repair. stewbsion.

Apr 28, 2011 | Night Owl Optics Explorer NOXB3 Binocular

1 Answer

We have the newcon optik. Wer took the batteries out to store it. We want to use itnow,put batteries in and it dont work. The number on it is (n99703638)

Hello there, alway check the battery. It can be check with a DMM for voltage but the battery needs to have a load on it. Hook up a couple flashlight bulbs across the + and - terminals. Then check the voltage across the battery with the load (bulbs). If the voltage across the battery is about 2.6v on a 3 volt battery with the load it's OK. Example: The same with your car battery that has a 12 volt system.---put a DMM across the terminals and it show approx 12 volts. Try starting the vehicle and if the voltage dropes below 10 volt while trying to start the auto, then the battery is or needs to charge. or it's bad Example, to check you vehicle to see on DMM if it is really charging. Start the vehicle and let it run, then check the voltage across the 12 volt battery. It should be 13.8 volts. This will indicate that the charging system of the vehicle is work. stewbison

Mar 22, 2011 | NewCon Optik Night Vision & Thermal Optics

1 Answer

Optics not working can not see anything through the optics, have changed the batteries and optic is making a humming noise

Hello, first did you install the batteries with it polaity the correct way. Negative - to spring side of the battery compartment. Postive + to the small flate plate. The hum could possibly be a shorted coil. When the short occurs, the electron leakage across the winding it will start to hum. Then the coil will completly burn out. stewbison

Feb 28, 2011 | Night Owl Optics Explorer NOCX3 Monocular

1 Answer

I need a I/R setup for these you have pr can you tell me where i can get one...thanks

Hello, contact Night Vision Optics they should be able to get you one. You can make your own by using an head light. Get an IR bulb, or change the lens to IR lens. If you want to high tech then get head light will IR LED's. If the white LED's are used don't use IR lens over this white LED's because of the light spectrum is different for the the LED's than incandescent light. They will have to be changed IR LED's..GB...stewbison

Jan 09, 2011 | Kalinka Baigish 12 Russian Night Vision...

1 Answer

Hi the ir is not working on my bushnell 26-0400,is there any way you can help (repair ?)

I had the same model, same problem. Bushnell replaced mine under warranty, If they needed to send it for repair it had to go to Russia. I guess it was cheaper to give me a new one. If its not under warranty Bushnell will send it off for you but it will cost quite a bit. My new pair lasted about 2 years with a lot of usage. Gen 1 night vision tubes do not have a very long life span. You may be better served buying a new pair of night vision binos.

Jul 08, 2009 | Bushnell 26-0400 Binocular

1 Answer

Detection Range of GS-7

It depends on the lighting conditions in the environment you're using them in. If you're in a field out in the country with no full moon, and only stars for ambient lighting... A Generation-2 set of goggles aren't going to see very far. But in the same spot with a full moon directly overhead you could theoretically see in excess of 800 yards.

That particular model has 3 different range settings for the Infrared Illuminator. Close, Medium, and Far. Although there doesn't seem to be any set value for the longest you can see, set by the manufacturer.

May 16, 2008 | Gsci GS7 Goggles

1 Answer

Night Owl Optics Cyclops Compact NOCC3 clicking and blinking

high voltage lead going into side of tube has poor insulation dissasemble carefully by removing screws behind lens put thick layer of silicone around joint wher white high voltage wire enters tube wait for silicone to dry fully before turning back on

Feb 04, 2008 | Night Owl Optics Cyclops Compact NOCC3...

2 Answers

Tasco nv 356 night binoculars

Check the HV to the tube and see if you can see any discolouration or spots on the tube - they often indicate tube failure. Many binoculars use the one power supply for both tubes as the current demand is very low. Often, one tube operation indicates tube failure, but a wire or connection could be at fault.

Nov 27, 2007 | NewCon Optik BN-5 Binocular

Not finding what you are looking for?
Fuji Stabiscope (7512404) Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fuji Night Vision & Thermal Optics Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers


Level 3 Expert

56961 Answers


Level 3 Expert

2042 Answers

Are you a Fuji Night Vision and Thermal Optic Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides