An expert who has achieved level 3 by getting 1000 points
An expert that got 10 achievements.
An expert that got 5 achievements.
An expert who has written 7 tips or uploaded 3 video tips
Re: jura impressa s9 is displaying error 1
The Owner Manual for the Jura Impressa S9 One Touch identifies Error 2 as being too cold and disabled for safety, but simply instructs to "Turn the IMPRESSA off at the power switch. Contact Customer Support in your country." for all other errors.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
How to reset / resolve Error 19H display IFB neptune DX
Follow following steps
1 power on the machine
2 push start / pause button
3 use + or - buttons to bring it to 0H
4 rotate cycle selector / circular knob to reset position
5 Display will change to 1.
6 again push the start/pause button to complete 1 min cycle.
7 after the display shows 0 . rotate cycle selector / circular knob to choose you preferred cycle.
Here are all the error codes and what you should do:
Codes E1: Water
Supply Error -Display
Shows 'E1' -Water
Supply Error occurs when water level frequency does not show changes more than
100Hz or water is not supplied up to the water level presetting for 20 minutes
or more at the time of initial water supply. -To
help fix this problem please check the Hot and Cold water intakes, there is
a filter screen in each input valve, remove and clean these filters. **
Make sure you replace the filters, they are very important for the operation
of the Washing Machine.** -The
error status can be cleared by turning POWER S/W OFF and resuming the POWER
ON initial status. E2: Water
Drain Error - Display
shows E2 -
case the water level frequency is 25.5Hz or less in the initial phase of UNB-detecting
cycle. - Water
Drain error can be cleared by turning POWER S/W OFF and resuming the POWER ON
status. E3: Over-Flow
Error - Display
shows E3 - Over-Flow
error occurs when the water level is too high. It can be
cleared by turning POWER S/W OFF, turn POWER S/W ON and then run the drain cycle
for 2 minutes. Water is drained prior to POWER S/W
OFF and it is forced to be drained for 2 min if a frequency of more than 25.24
KHz is detected Door Open Error: - Display
shows door - This
can fixed by closing the door E4: Unbalance
Error - Display
shows E4 - Laundry
load is unbalanced; loosen any tangled laundry. - If
only one item of clothing needs washing, the final spin result might be unsatisfactory
and an E4 error message will be shown in the display window. - Unbalanced
error is cleared by POWER S/W OFF and by resuming the POWER ON initial status E6:
Please see "Eb" at end of
list. E7: Pressure
S/W Error - Display
shows E7 E9: Water
Leakage Error EA: Tacho
Error - Display
shows EA - This
is error can be cleared by turning the power off and then on again. Eb: Motor
Triac Short Error - Display
shows Eb - This
is error can be cleared by turning the power off and then on again. E6-EB
only be corrected through Service. Please contact Customer
Service Department at 1-800-SAMSUNG (option 1-1-2) to schedule an on-site service
call for english service.
Thank you for using FixYa. Have a nice day and please remember to rate this solution as if it helps you.
This error is because:
1- Flow meter is blocked & not sending signal of water flow.
2- Entire hydraulic system is filled with Calcium deposits and slowed down flow of water.
1- Open the machine and manually clean flow meter. It is located between the water tank & the pump.
2- Follow this by manually descaling the machine. Seelink. Do not use automatic descaling method suggested by Jura.
Stop using Filter cartridges as the machine reminders for descaling are silenced by use of filters. Services Unlimited Inc Parts Guru Since 1988
Juani, can you use ground coffee in your machine. Then go and find the grinder and put some coffee beans in and grind them.
while enjoying your coffee read the user manual for the coffee machine and find out what the trouble is. If you can't find the manual, you can get it here Free User Manuals and Owners Guides ManualsOnline com
all the best Kolbrun
Could be bad grinder or no 12v. The display/control runs on 5v and there is a transformer (supplying 5/12vdc) where the a/c cord comes in. Mine was blown from lightening.
Try these guys... they have parts, trouble shooting and videos on youtube. http://www.partsguru.com/JuraCapressoImpressa.html
Error 4 is in Plain text a Temperature measurement error in steam cycle (circuit)
Causes / Remedy:
Sorted in order of likeliness !!!
1) Thermal sensor is defective. Determine the resistance value at 20 degrees C to be about 12kOhm. - Replace thermal sensor if not.
2) Cable broken to the thermal sensor or oxidized contacts. - Replace / repair the cable.
3) Logic board defective - replace electronics / replace EEPROM.
If you want to do the job yourself. Parts for repair solutions above are
1) Replacement Thermal Sensor with cable GBP 19.99 plus postage
2) if you can fix broken wire or oxidized contact no need for parts
3) logic board GBP 198.99 plus postage (there might be the possibility to have EEPROM on the board replaced at a fraction of the price. Defective board must be sent in first.
It also is possible to sent in the machine for repair.