Question about Ricoh Office Equipment & Supplies

Open Question

Ricoh SP c320 Dn service code SC543

I have a ricoh SPc320 DN which is showing the service code SC543. I don't seem to have a yellow button or the digit buttons as mentioned on previous answers. Please help

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
drichards
  • 87 Answers

SOURCE: RICOH AFICIO SP C411 DN COLOUR LASER PRINTER

Open the side cover, and unlatch the plate. The PCUs are located in there. In the replacement PCU, there should be instructions.

Posted on Apr 01, 2008

Ad
Bubbabear64
  • 2794 Answers

SOURCE: RICOH 2015 error code sc 500

Main motor/ transport motor lock/ fusting motor error.

The only thing you can do is check for any obstructions in the machine.

That needs to be looked at by a service because the problem could be a motor, a pcb, or a power supply.

It can be a lot of troubleshooting to do.

Posted on Oct 19, 2008

  • 4 Answers

SOURCE: Ricoh SPC411 DN Error

dirty ID sensors on transfer belt clean with canned air or replace. Careful not to spray liquid freon on transfer belt or you will replace that too!

Posted on Dec 15, 2008

  • 126 Answers

SOURCE: sc 481 on my ricoh aficio 1224

moz-screenshot.jpgmoz-screenshot-1.jpgThe problem (s) could be; defective main motor, image transfer belt out of position, belt mark blurred or absent.

A ITB belt inspection and/ or repair would be a job for tech.
Or you could just order a new PCU which would fix the problem.

Posted on Jan 08, 2009

  • 126 Answers

SOURCE: machine shows a service code of sc 928

The SC - 928 is a Memory error problem.
The machine detects a discrepancy in
the write/read data during its write/read
test (done at power off/on and at
recovery from low power or night/off
mode). To try to reset this code -- Turn the MAIN power switch off, wait about 30 secs. then turn switch back On.

Possible causes:
• Memory defective
• BICU defective
• Poor connection between BICU and
memory
The cheapest repair would be to replace the memory. It is rare the the connections came apart unless some one was in the back of the machine for some reason.

Posted on Jan 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Iam getting sc543 for ricoh aficio printer SP C220N,Kinly help


Its a fuser error code Must be reset sp 5-810 in service mode.-Carl

Sep 18, 2017 | Ricoh Office Equipment & Supplies

1 Answer

Service manual for Ricoh Aficio SP 5200 DN with all parts and troubleshooting


go to service mode.

press up and down button. then press ok. go to SP5810 and reset.

Jan 29, 2017 | Ricoh Aficio SP 5200 DN Laser Printer

2 Answers

Error sc543 sp c320dn


SC542, SC543, SC544, SC546,
These codes are related to fuser temperature. Make sure that power source voltage are not low. check thermisters, fusing lamps etc. To reset this code press "All clear" yellow key, enter 107 and press the red key for some seconds. Sevice mode will be displayed, enter SP 5-810 (SC code reset) and select "1". Then hold down the Photo mode key and the # key at the same time for at least 3 seconds

Feb 17, 2012 | Ricoh SP C320DN AllInOne Laser Printer

2 Answers

Ricoh 410 DN SC545 error code


This is a code for fusion.
Check:
- Thermistor
- Thermostat
- Lamp

Dec 30, 2010 | Ricoh Aficio SP C410DN Laser Printer

1 Answer

Ricoh Aficio SP 232 DN access code.


Call a Ricoh Technician to Reset the codes

May 30, 2010 | Ricoh Aficio SP C232DN Laser Printer

3 Answers

SC543 ricoh Aficio 1027


• Fusing thermistor defective or out of position
• Fusing lamp open
• Fusing thermostat open
• Poor connection of the fusing unit
Inspect all the elements before mentioned, soon presses total clear (Yellow Key) 1 0 7 and Maintain pressed clear stop key (orange key) more tan 3 sec. Enter SP 5-810 (SC code reset),
select execute, select close. Exit SP mode, turn the main power
switch off then on.

If the problem continuous the problem can be in the Power supply board, can be defective.

Aug 10, 2009 | Ricoh Aficio 1027 All-In-One Laser Printer

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

400 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ricoh Office Equipment & Supplies Experts

Adorjani Laszlo

Level 3 Expert

1297 Answers

quennie732

Level 2 Expert

398 Answers

OfficeServiceAjnc
OfficeServiceAjnc

Level 2 Expert

203 Answers

Are you a Ricoh Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...