Question about 3M Scotch-Weld Epoxy Adhesive Dp125 Gray Duo-Pak

1 Answer

Weld pak I have a Lincoln Weld Pack HD. I turn it on the fan is running the wire feeds, but no ACR ???

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Master
  • 14,161 Answers

Posted on Jun 23, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have no gasflow it sounds as if the gas is leaking at the feed rolls


there is no seal at the feed rollers around the wire as it requires the correct gauge wire and feed hole to slow down the loss of gas at that point ( easier for the gas to escape up the wire housing and out the welding end )
the gas is allowed to flow when the welding trigger is operated as that opens a gas solenoid that allows gas to the welding wire tube to exit past the shroud around the welding point

read you user manual well to be acquainted with the machines operation, and if there is a persisting problem talk with your supplier and consider a warranty service check

Sep 15, 2016 | Lincoln Electric Weld Pak 140 HD Wire Feed...

1 Answer

Weld-pak 100 Hd Problem


There is a reset button located in the wire feed spool compartment,
check to see it stays in when pushed. It is a safety when the machine
overheats, it normally resets when machine cools off. If it is working properly I suggest contacting Lincoln Electric Dealer for service.

Mar 03, 2012 | Lincoln Welding Tools

1 Answer

Where can I get a gas diffuser for a Lincoln Electric Weld Pak HD wire feed welder?


Gas diffusers are sold at any welding store, look up praxair site for your nearest location. The part number you are looking for is: TWE-35-50 about 6.00 bucks or less.

Jun 13, 2011 | Lincoln Electric Welding Tools

1 Answer

I have a lincoln weld pack 100 hd, and i want to weld aluminum but i dont know how to start. i buy a 4043 fil d aluminium mig and i dont know if my welder it ill be fine to weld,


you can weld aluminum with the lincoln but you will need to change the liner in the wand to a nylon one and swich the gas to 100% argon and of course change the wire to an aluminum roll. and practice-practice-practice it is much more difficult to weld aluminum then steel and requires much more control.

Feb 03, 2011 | Lincoln Welding Tools

1 Answer

My weld pak 100 will not feed the wire


you Ned to check if the voltage selector is in good condition if not replaced.

Jan 03, 2011 | Lincoln Electric Century Portable Plasma...

1 Answer

I have a Lincoln Weld Pak 100 that was working fine. I shut down the machine though and when I came back to it about 5 hours later the wire feed motor wouldn't turn anymore. Has anybody else had the same...


Check the voltage at the wire feed motor when the trigger is pulled.

I had a Weld Pak 100 that with 0 volts at the wire feed motor, and the problem wound up being that 2 of the big power (stud) diodes were shorted.

Feb 26, 2010 | Welding Tools

1 Answer

Lincoln 3200hd. welder,when power switch turns on, the fan comes on, but when i pull the trigger on gun to start to weld nothing happens the wire does not feed. i am not sure what is happening


open the area were the role of wire is and check when trigger pulled if any action to feed motor. [wire might be stuck at end, or there usually is a small fuse in that area for feed motor]

Dec 04, 2009 | Lincoln Electric K1170 AC-225 Stick Welder

3 Answers

Lincoln Weld Pak 100 arc welder troubleshooting


There can be a switch that makes the wire electrically "dead" so it can be fed through the liner. Also suitcase style welders have a sensor wire with a clamp that must be connected for the arc to be able to be struck.

Nov 22, 2009 | Welding Tools

2 Answers

The wire feed on my welder will not work.


Maybe you can get lucky like I did . Some times the acr volt selector switch gets corrosion in it and wont let the circuit board know to send power to the wire feed motor. You can cycle this arc volt. switch in my case it is the a,b,c,d,e, switch back and fourth a few times and this will brake the corrosion and your wire might feed again as mine did . This corrosion build up happens from not using and or sollecting the switch much usually on a welder at hm that gets very little use. it is common good luck .

Jul 24, 2009 | Lincoln Electric LINK2400-+2 CV-305 MIG...

Not finding what you are looking for?
3M Scotch-Weld Epoxy Adhesive Dp125 Gray Duo-Pak Logo

Related Topics:

470 people viewed this question

Ask a Question

Usually answered in minutes!

Top 3M Adhesives, Coatings & Sealants Experts

kakima

Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Richard Piatek
Richard Piatek

Level 2 Expert

88 Answers

Are you a 3M Adhesive, Coating and Sealant Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...