Question about Audio Players & Recorders
It is brand new and channel 1 just has really low sound with clicking.
Could be a bad amp or blown speaker. If you have a meter you can test the speakers.
Posted on May 13, 2013
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: cerwin vega ve-28s
I had same prob ans cerwin replaced part in amp, it happened again few months later so they replaced entire amp assembly. i am very happy with it, they are a great sub, loud and deep.
Posted on Mar 05, 2008
I bought my VE-28s and it did exactly that crackled, cerwin replaced part in amp but few months later problem persisted. they then replaced entire amp assembly and its been fine. i really push it to and its been fine. to test it, unplug the connection from amp/ reciever and see if it persists. if so its the sub, if not its the amp/ reciever. dont dump it, these subs really crank and can put out some deep loud bass.
Posted on Mar 05, 2008
first you need a multimeter set to OHM , check on the back of the horn , remove the leads and do some reading , it should read 4 , 8 , 16 ohms depending of the brand , if you get no reading its means that need to be replaced , some horns you can detach the back (magnet w/the coil ) so you can replace it without buying the whole unit . good luck
Posted on Apr 19, 2008
We will start with the easy one, Phase. The phase selector is a setting that can be adjusted by sound; which one sounds better? Either one will work fine. It's mainly for situations where the sub enclosure is located at a distance or behind the listening area. The 'in and out' crossover selector and the input from the receiver goes together. The 'in and out' crossover selector is asking if you want to use the internal crossover to block the bass from getting to the satellite speakers. Most home surround sound receivers only have the one sub out and most subs have both left and right inputs. When there is a single signal being fed to the sub you use the subs left input or buy a splitter and send the signal into both left and right, but either way will work equally the same.
There is two ways to connect the speakers to the receiver.
1) Cross-over 'In': you connect the output speaker wires from the receiver to the speaker inputs on the sub and the speaker outputs on the sub to the satellite speakers; the sub will get its sound from the input speaker wires.
2) Cross-over 'Out': you connect the sub to the receiver using the receiver's single sub out, then connect the satellite speakers directly to the receiver's speakers outputs; in this configuration the satellite speakers are given a full range of signal including the bass.
I have used #2 with the same system and had great results.
Posted on Aug 13, 2010
SOURCE: V-35 Cerwin Vega
Turbo 37: Did you ever root cause your V35's? I just ran across this post. I own a pair and have done some amateur / professional speaker building. Let me know if you still want to repair. tro
Posted on Apr 02, 2011
Tips for a great answer:
Jan 25, 2015 | Audio Players & Recorders
Mar 16, 2012 | Cerwin Vega Cerwin-Vega E-715 Floor...
Mar 19, 2011 | Cerwin Vega AVS-5.1 System
May 10, 2017 | Audio Players & Recorders
Aug 18, 2010 | Cerwin Vega V-152 Main / Stereo Speaker
Jun 22, 2010 | Cerwin Vega 2 Channel Amplifier - Vega...
Feb 11, 2010 | Cerwin Vega V-6F 6 1/2" 2-way...
Jan 05, 2010 | Cerwin Vega LS-15 Speaker
Oct 28, 2007 | Cerwin Vega VE-28S Subwoofer
29 people viewed this question
Usually answered in minutes!