Question about Onkyo TX-8211 Receiver

Open Question

Protect mode i added a amplified receiver and now if i turn the volume up it goew into protect mode

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Onkyo Tx-v940 Receiver/Amplifier Protection Mode

Audio amplifier IC's damaged you need to change it.Good luck

Posted on Jun 11, 2008

  • 151 Answers

SOURCE: onkyo ts595 goes into protect mode with volume increase

HI check your speaker cables are not touching, also make sure "b" speakers are not on and that all your speakers are 4ohm or higher as this will cause the amp to shut down if they are to low an impedeance,The amp is protecting itself when it shuts down.

hope this helps.
CABLE GUY.

Posted on Aug 05, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Protect mode?


You added speakers in parallel which reduced the effective impedance to to a value low enough that your Rockford Fosgate amplifier had to enter protect mode to prevent damage to its output stages.

Jan 22, 2014 | Car Audio & Video

1 Answer

My denon avr1200 receiver once it is turned on goes into Protection mode. How do you reset or make work?


The reciever will go into protection mode when there is a short in the speaker wires or the amplifier was overloaded. What I would do first is verify that none of the speaker wire connections are loose at the back of the reciever or at each speaker. And verify that none of the wires are making contact with each other. Then label each speaker wire as you remove them from the reciever so you can re-install them correctly. After you have disconnected the speaker wires try unplugging the reciever for 10 to 15 minutes. Most recievers have a self-resetting overload protection switch and this should reset it back to normal. Now try plugging the reciever back in and turn it on without the speaker wires connected. It should be out of protection mode now. If it is still in protection mode verify that there is not a reset switch somewhere on the back of the reciever. If it is not in protection mode now then proceed to connect one speaker set at a time and turn on the reciever to see if it goes into protection mode. If it goes into that mode after connecting a speaker then that speaker is the cause of the problem. If it does not go into the mode after all speakers are connected then try turning the volume up. If it goes into protection mode then there could be an internal short on the amplifier or a incorrect OHM rated speakers connected to reciever. Verify that the speakers are rated the correct OHMS.

Feb 22, 2010 | Denon AVR-1200 Receiver

1 Answer

Harmon Kardon Citation 22 amplifier is in protect mode


Maybe there's a correlation to those devices being attached. Float the the amp so it has no cables to anything and figure out why it's going into protect mode. If it doesn't, start adding units until it does.

Feb 04, 2010 | Audio Players & Recorders

2 Answers

Sony STR-DE835 5.1 Channel Receiver When looking at the Sony Service Manual Supplement-1 There are several modifications to receiver does anyone know the reasons for these Mods?


THIS IS NOT A MODIFACTION ,ITS AND ADDITION TO THE ORGINAL SERVICE MANUAL WHERE THEY LEFT OUT THESE PARTS ON THE ORGINAL SERVICE MANUAL.

Dec 04, 2009 | Sony STR-DE835 Receiver

1 Answer

I got a pyle 1800w amp and a 1500w kenwood subs but as i increase the volume in the headunit it goes on protect mode why the other problem i got is as increase the volume in the headunit the bass of the...


The protection modes in these units ****. Most new units have them. What I do is turn down settings on deck and turn up amp as much as possible. Then the protection won't turn on because you won't have to turn it up as high.

Sep 30, 2009 | Pyle PLA1200 Car Audio Amplifier

2 Answers

My Sony XMGTR2022 goes into protect mode at


I discovered that there is a compatiblilty problem between the Bose receiver and the Sony amplifier. If I disconnect the receiver from the amp then the amp starts up normally. Apparently the receiver sends out a dc offset or a "thump" that the amplifier doesn't like and goes into protection mode. I solved the problem by putting a 1 second delay circuit between the receiver startup and the amplifier startup. A simple RC delay on the remote input to the amplifier solved the problem.

Sep 03, 2009 | Sony Xplod 1200W Class AB Bridgeable 2-Ch....

1 Answer

The receiver goes on standby mode when volume is high


Your receiver is basically going into protect mode.

The SR 605 contains a microcomputer for signal processing and control functions. In an unlikely event, it may cause it to lock up. Unplug the power cord from the wall outlet, wait for 10 to15 seconds and then plug it back again.

Please also check your speaker cabling again. Make sure that all of them are seated properly, none is touching each other or the body of receiver. Take out all the wire and put them back again if necessary..
Some times even a little tiny frayed wire touching the receiver could trigger the protect mode. Be careful, since protect mode is sometimes not fast enough and it could blown a few trasistors in the power circuit.
Just check your speaker as well....whether they play all right thru another receiver or amplifier. its posiible they might be shorting inside. A little frayed wire could also trigger the protect circuit in your receiver.
I hope this should solve your problem. If you still can’t resolve the issue yourself, try resetting
the AV receiver/AV amplifier before going on to opening the Receiver.
To reset the Receiver to its factory defaults, turn it on and, while holding the [VCR/DVR] button, press the [STANDBY/ON] button. "Clear" will appear on the display and the Receiver will enter Standby mode. (note that resetting your receiver will delete your custom settings as well as your radio presets).

If everything else seems all right and still your receiver shut down when you raise the volume then it possible that there are bad connections on the main board that are set in.

This would generally happen if the system is slighly old or have dry solder and when you raise up the volume. This should be a simple repair that will not require parts. If you can solder, you will be able to repair this yourself. If not, then a local service center will change the local labor rate.

Hope you can sort out your problem with the above trouble shooting. Let me know if I can guide you further.
Best of luck. Thanks for using FixYa!

Mar 13, 2009 | Onkyo TX-SR605 Receiver

1 Answer

No sounds


Test one speakers at other amp to ensure its working. Amp is going into probable protection mode. Disconnected all speaker and av wires (only power) turn up volume and see if it stays on. If not sounboard or volume function faulty. If on, connect one speaker L or R. Go to tuner mode to tuned radio station an listen for sounds. If sound connect speakers and av cables one by one and test each one on its own until amp switches off, or no volume. Investigate from there were prolem is.

Feb 25, 2009 | Pioneer VSX-D710S Receiver

2 Answers

My kenwood amplifier suddenly off when i turn the volume high?


You need to make sure you ohms are correct if there too low this will happen to protect the amp.

Dec 03, 2008 | Kenwood KR-V7080 Receiver

2 Answers

Protection mode


you have to verify your connection cause if you are a short circuit in your different output or input the protection mode is on. it's an internal security
first disconnect all your output speakers, and restart your amplifier if the protection mode is on again try to disconnect all your input device and restart your amplifier, the protection mode should be off, so after connect one device after one to check who makes your protection mode on
;)

Mar 31, 2008 | Onkyo TX-SR502 Receiver

Not finding what you are looking for?
Onkyo TX-8211 Receiver Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Onkyo Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5047 Answers

The Knight
The Knight

Level 3 Expert

74106 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you an Onkyo Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...