Question about Sharp AL 800 Copier

2 Answers

Sharp AL-800 copier

Paper jam light is blinking and won't let the copier work. I've already taken the jam out and clean the drum 4 times. Still won't work.

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had the same problem with the same machine. I removed the cartridges and blew out the insides with an air hose. All better now!

Posted on Sep 13, 2007

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 328 Answers

If you check in the unit where the paper first leaves the paper tray, there is a small black lever called a sensor flag that should move freely in and out of a sensor led.Also one or two more inside the machine and where the paper exits the unit.

I’m happy to help further over the phone at https://www.6ya.com/expert/jayw_0e86fb055a7b73de

Posted on Aug 07, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My AL-800 l has a paper jam indicator light that stays on. I find no paper jam. Can you help!


open all the doors and look for anything including paper dust. It doesn't take a sheet of paper to cause this just a sliver or a spot of dust You can use a clean paint brush to brush anything or a vacuum hose or even a can of compressed air. If that doesn't fix it then you may have a sensor problem which usually means it is time to get a new printer as the sensor will cost as much as a new one (unless covered by warrenty)

Mar 23, 2010 | Sharp AL 800 Copier

1 Answer

Sharp AL-800 light copies


Check the machine for a **** or dust glass above the drum.
Check and clean coronas, the wires and shells may be dirty reducing charge.
Run a few white copies, to check of the toner / carrier ratio is low.

Hope this is of some help.
Ed

May 11, 2009 | Sharp AL 800 Copier

1 Answer

"P" is blinking. There is no paper jam. Paper is not feeding from the paper tray.


Hello sir; there is paper pick up roller dirty or worm, need to clean or replace.

Apr 28, 2009 | Sharp AL-1451 Laser Printer

1 Answer

AL-800 cannot make copies jam light remains on with no jams


First, is the paper being fed at all? If the paper is being fed and jams at the same location then a senor, actuator or switch is bad, out of place or broken. If the device will not clear the jam light, completely power down the device, unplug from wall, let set about 30 sec. to 1 min. and then replug in and see if it reset. If the device did not reset then again a senor, actuator, or switch is out of position ( being held up in the paper path). If the paper does not feed at all then the feed section is the problem. Clean the feed tire (s) the rubber restorer or a high alcohol base cleaner. Listen to hear if the feed tire (s) are even turning. If feed is not turning then it could be clutch, motor or board problem.

Jan 04, 2009 | Sharp AL-800L Copier

1 Answer

Sharp AL-1631 Copies has begun to print verticle lines on page.


if the drum already been scratched out,so there is no solution to repair it,u have to change the drum.before change the drum check the copier glass surface if any dry up material,wipe it with dry cloth.

Dec 09, 2008 | Sharp AR-5320 Black and White Copier

1 Answer

Cant get the paper jam paper to turn off and work again


1- either there is something stuck on the sensor or
2- the sensor is bad or out of place

Aug 19, 2008 | Sharp AL 800 Copier

1 Answer

Misfeed indicator


It could be comming from the paper feed mechanism above the paper tray. Make sure its installed properly. It could be as simple as cleaning the feed tires.

Jul 12, 2008 | Sharp AL 800 Copier

1 Answer

Sharp AL-800 Paper Feed


Is this something that has been getting worse or just happen at once? If it just appeared it good be something in the paper tray stopping it from liftting or something behind the paper tray or in the paper path of the copier. If it has been slowly happen try to clean the paper pickup rollers with WD-40 and a rag and clean the rubber only. If that works you done, but if it say's to add paper you may have a broken paper present sensor. The jams could also be the paper feed clutch is worn out. Worse case use the bypass tray. Good Luck!!

Feb 07, 2008 | Sharp AL 800 Copier

1 Answer

Sharp AL-1641CS printer/copier


Most likely you had a toner cartridge failuer leaving some of the ink and developer in the crevices above the paper feeder and its just trickling onto the paper.
It pretty much needs to have the cartrides taken out and thouroghly vaccumed.
Just takes patience and time to get it all removed.
Dont vacuum the cartridges, but the inside of the machine.
Pull your paper tray out and see if there is toner and developer trickling into it.

Jan 09, 2008 | Sharp AL-1641CS All-In-One Laser Printer

Not finding what you are looking for?
Sharp AL 800 Copier Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Office Equipment & Supplies Experts

Anthony Karuku

Level 2 Expert

257 Answers

k24674

Level 3 Expert

8073 Answers

jasbo
jasbo

Level 3 Expert

2237 Answers

Are you a Sharp Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...