Question about Cell Phones

Open Question

Plastic bezel sharp shp4023 384

Not warking

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to change battery in EH23sa


The battery is actually accessed from the front of the watch.
You should have a "Case Knife" to remove the front bezel.
Remove the band first.
Set the watch in its side. Set the case knife at the groove where the watch band holder meets the front bezel, and give the back of the knife a sharp rap with a small hammer. The front bezel should pop off.
Some watches have a small circular plastic piece that will also come out. Gently remove the movement from the front. The battery (CR 2025) can then be removed from the back of the movement using a small, thin blade. Install the new battery. The inside back of the case should have restart instructions. (Push A -left button once. then push and hold A until hands move to 12:00. Push B once to start reception.
The back of the watch is plastic. Don't try to remove it.
Gently re-assemble movemengt. A watch case press tool is best for finishing assembly. I would suggest taking the watch to a jeweler if you are uncomfortable taking this watch apart. Good luck






Mar 21, 2011 | Watches

1 Answer

How can i replace my webcam plastic cover on my toshiba satellite L505?


you may need to buy the whole bezel around the LCD, if you have the bezel you jus use a pry tool to open the plastics tabs around the LCD bezel.

Mar 15, 2011 | Toshiba Satellite L505-S5966 Notebook

1 Answer

Replace tailgate handle 2002 avalanche


If it's similar to a Silverado, the tailgate handle consists of a bezel (plastic cover) and a Red and Green plastic clip that break very easily. Take the bezel off (just pull carefully from the tailgate, careful not to break the plastic clips) look for 2 rods, again 1 connects to a red clip, the other to a Green, replace the broken one, or a cheap/temporary fix is to use a plastic zip tie at the connection. Snap the bezel back in.

Jan 23, 2011 | 2005 Chevrolet Avalanche

1 Answer

How to change out a broken lcd screen on an aspire


http://www.insidemylaptop.com/remove-lcd-screen-replace-inverter-board-acer-aspire-5100-laptop/
This is its contents without the pictures:


OK, let’s get inside the display assembly.
First of all, turn off the laptop, unplug AC adapter and remove the battery.
The screen bezel* has four screws hidden under for seals. Two rubber seals on the top of the bezel and two plastic seals on the bottom.
You can remove all four screw seals with a sharp object as it shown on the picture below. Glue removed seals somewhere on the bezel so they don’t get lost.
Remove four screws found under seals.
Start remove the screen bezel with your fingers. Proceed slowly while removing the bezel.
Carefully separate the display cover from the screen and access the LCD cable connector
You’ll have to unplug the LCD cable from the screen.
First, unglue the clear sticky tape securing the connection.
Second, unplug the LCD cable from the connector on the screen.
Here’s how you can remove the LCD screen.
Simply remove four screws securing the LCD screen to the display hinge. Remove four more screws from the other side of the screen.
Now you can remove and replace the LCD screen with a new LCD screen.
Put all the screws back in there places

Dec 31, 2009 | Acer Aspire One PC Notebook

1 Answer

Can't figure out how to remove inside door handle bezel on 1995 K2500 6.5 TD


Removing the bezel is with a small flatblade between the door handle and the bezel, there are two or three plastic clips that you gently pry towards the outside of the bezel while pulling out on bezel. Don't try this when the car is in cold conditions if possible as the plastic is more brittle then. Best to do inside heated garage or after heating up bezel somewhat.

Nov 30, 2009 | 1997 Chevrolet K1500

1 Answer

Replace LCD screen


No, Remove the Screws On the Front Bezel Of the Screen.. (there should be 4 One on each corner), Then you will need a thin plastic tool such as a guitar pick or thin credit card... Pry the front plastic bezel from the back cover starting at the top right corner.. THe Whole Front Bezel Is Held On By Snap Down Plastic Tabs... You Will Need To Slide The Plastic Tool Along The Entire Top Of The Screen At an Angle... Then Once the top is insnapped, Do the sides, Then The Bottom.. Front Bezel Is Now Off And You Should Have Full Access To The Display...

You will have to Unscrew the screen from the Hinges On THe Left And Right Sides... Usually 2 or 4 screws on each side then screen is removable

Nov 17, 2009 | Acer Computers & Internet

2 Answers

How do I remove the invertor from a Qosmio F20?


The inverter is located behind the bezel at the bottom of the screen/lid and in between the hinges.
The bezel has screws that fixes it to the lid and these can be hidden by stick-on plastic covers. Use a thin sharp point to lift these plastic covers off to reveal the screws. Remove these screws.
The bezel has small plastic catches that clips it to the lid and may also be fixed to the LCD screen with double sided tape. Use a thin blade and insert it between the LCD screen and the bezel and gently ease the bezel off. Start at the bottom of the screen and gradually work along the edge and continue around each side to free the bezel.
Be CAREFUL not to scratch the LCD screen and DO NOT apply too much pressure to the face of the LCD screen because you can crack the glass surface and ruin the LCD screen.
Once the bezel is removed then you can get access to the inverter to remove it.

Nov 16, 2009 | Toshiba Qosmio G15 Notebook

1 Answer

How do I remove the bezel from my hp l1955 monitor


There usually screws hidden behind stick-on plastic covers on the front and or edges of the screen. Use a sharp point to lift off these covers to reveal the screws.
The bezel will also have plastic catches/clips that secures the bezel to the lid as well as double sided tape. Slip a thin blade between the glass screen and bezel and gently lift the bezel free. Start at a corner and gradually work along each side.
Be careful not the apply too much pressure on the glass (it is easily cracked) and be careful not to scratch the screen.

Nov 15, 2009 | HP L1955 19" LCD Monitor

1 Answer

Need instructions to replace the bezel on a gateway 7330gz


Just like any other laptop LCD screen, edtechservic. Remove the rubber caps that cover the Philips head screws, remove the screws, and work around the bezel to pop it loose, a little at a time.

Top cover up, you are looking at the LCD screen. Look at the top Left and Right corners of the screen bezel. Look in-between. Now look along the bottom of the screen bezel. See those small rubber caps? G-E-N-T-L-Y pry them loose with a 60 or 90 degree pick. (In your computer repair kit)
Use care, and finesse! You don't want to scratch the clients laptop!
Now loosen, and remove the screws underneath.

Use a Jewelers flat tip screwdriver, (No.2), and ease it in the parting line, that you will see between the bezel, and top cover. Don't go more than a 1/4 inch in! You could be up against the LCD screen metal frame, if you go too far in. (Which could break the LCD screen)

Won't ease in there? Move over an inch or so. You could be hitting the plastic part of the bezel, that snaps down into the Top Cover.
There are several of these plastic protrusions, that stick down from the bezel, and snap into place in the Top Cover. Every few inches or so.

After you start easing one of these plastic snaps out, (Plastic protrusion I spoke of above), move along the edge, pick another place, and start easing it up. Keep bringing the edge up a little at a time. (Bring the back of the flat tip jewelers screwdriver down)
When you have gone along, and raised a large portion of the bezel, you should hear a distinct Click, as one of the plastic snaps come out of the Top Cover.
If not, move back to the first plastic snap that started to come out, and place your flat tip Jewelers screwdriver next to it. Bring the back of the screwdriver down to pop that plastic snap up, and out.

Hearing it your first time might make you a little stomach sick. You'll think you broke something! If you go along, and raise the bezel up a little at a time, you'll be okay. The bezel is made of space age plastic, and is VERY tough! You can't get crazy with it though!

When you have gone almost all the way around the bezel, the last few inches may just pop up, and out.
This link shows you with photos, and information, for a Gateway MT6704 Notebook PC,

http://www.insidemylaptop.com/remove-lcd-screen-from-gateway-mt6704-model-ma7/

This guide is to completely replace the LCD screen. You can just use the information under the first five photos, for bezel replacement.



Nov 15, 2008 | Acer Aspire 3000 Notebook

Not finding what you are looking for?
Cell Phones Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cell Phones Experts

Computer Repairing
Computer Repairing

Level 3 Expert

14641 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

William Alequin

Level 3 Expert

922 Answers

Are you a Cell Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...