Question about Maytag Washing Machines

1 Answer

Pavt454eww how do I get the pulley off the motor?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Maytag Master
  • 42,073 Answers

Look for a grub screw in the hub of the pulley. take it out and you will most likely need a 3 /2legged puller to get it off the shaft You may be lucky and have a bolt in the end of the shaft and the pulley will slide off

Posted on Apr 27, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Knocking noise when printing


Check the following:


1. DC motor assembly.
Make sure all the motor plate mounting screws are tight.


2. Idler pulley - DC motor assembly.
Make sure the idler pulley is not binding on the pulley shaft. Check the pulley for wear. Check the idler pulley shaft on the motor mounting plate for damage or contamination.


3. Drive pulley.
Check the drive pulley for wear, binds or damage to the pulley or pulley shaft. Make sure the pulley turns freely on the pulley shaft.


4. Motor drive belt - tray drive belt.
Check the DC motor drive belt for damage. Make sure the belt is tracking correctly on the drive pulley, idler pulley, and motor pulley. Check the tray drive belt for damage. Make sure the belt is tracking correctly on

Dec 11, 2012 | Lexmark X646e Laser Printer

1 Answer

The belt on my Kenmore washer model no. 110.45091401 is shredded. How do I replace it?


REMOVE BACK PANEL ON FRONT LOAD WASHER PUT BELT ON LARGE PULLEY AND TAPE BELT TO LARGE PULLEY TAKE OTHER SIDE OF BELT AND STRETCH TO MOTOR PULLEY WHILE ROATING LARGE PULLEY WALKING BELT ONTO SMALL PULLEY OR LOSEN MOTOR BRACKET PAY ATTENTION TO LOCATION OF MOTOR BRACKET ALIGNMENT PUT BELT ON BOTH PULLEYS PUSH MOTOR TILL BELT IS TIGHT AND RETIGHTEN BELT

Jan 26, 2011 | Kenmore Washing Machines

1 Answer

The belt skips when walking or running


Take the motor hood off and set aside. Straddle the walk belt and set the speed to 3 or 4. Take one foot and step on the walkbelt hard. While doing this look at the pulley on the front roller. Does just the roller stop and the pulley keeps turning, does the roller and the pulley stop together or does just the walkbelt stop? If the walkbelt is the only thing to stop it is loose. If the pulley, roller and the walkbelt stop the motor belt is loose. If the pulley continues to turn and the roller and walkbelt stop your pulley is slipping on the front roller ( press fit). Two solutions: 1) replace the front roller or 2) pin the front roller to the pulley. Align the pulley roller to the motor pulley by tapping it into position. remove motor belt by loosing motor. Drill 1/8 hole through the pulley and roller. Take a larger drill bit and countersink the pulley hole so the head of a screw will be below the pulley grooves when installed. install the screw. If you mess it up -- turn the pulley and roller and try again. This is a permanent fix for this problem. You may have a little pulley wobble and that is OK.

Jan 15, 2011 | Epic 425 Mx Treadmill EPTL88105 !

1 Answer

I have a maytag pavt454eww. I am looking for a fuse or a thermal circut breaker somewhere. The motor smelled hot and shut off. Is there something in the circut to protect the motor?


YES, THERE IS A OVERLOAD PROTECTOR ON THE MOTOR ITSELF. THERE HAS TO BE A REASON WHY THE MOTOR IS GETTING EXCESSIVELY HOT. PROBABLY A BEARING THAT IS BINDING.

Mar 30, 2009 | Fisher Paykel EcoSmart GWL15

2 Answers

Need to install new motor on Maytag PAVT454EWW


try going to partselect.com to find the parts they have a picture breakdown of your washer and you can buy the parts right there

Mar 10, 2009 | Maytag Performa PAV2200

2 Answers

Maytag 2005 washing machine top load model number PAVT454EWW makes a loud grating noise when it seems to be in a agitation cycle, and the motor is running and the belt is working, but the agitator is not...


HI thanks for the question. yes it sounds like the tranny. Maytag has 5 yr warranty on the tranny. have it replaced thanks the appliance doc. please rate my answer.

Oct 07, 2008 | Washing Machines

1 Answer

Maytag PAVT454EWW pump 21002240


Don't worry about it, you can install the new pump with out the plate. It will work just fine. They must of redesigned it. I get them this way all the time, Catriver

Sep 22, 2008 | Maytag Performa PAV2200

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

213 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

587 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...