Question about Hoover U6434-900 Bagged Upright Vacuum

Open Question

Hoover carpet scrubber brushes wont turn - Hoover U6434-900 Bagged Upright Vacuum

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

reddevil6
  • 1673 Answers

SOURCE: Belt replacement Hoover carpet cleaner

Hoover steamvacs don't use belts. If the brushes are not turning, pull the brush block out, turn the machine on and see if the square hole where the brush block was, is turning. If not then the turbine is bad. Sometimes you can take the turbine apart and clean it out. most times I have found , replace it.

Posted on May 26, 2008

  • 1 Answer

SOURCE: Hoover SteamVac Dual V Carpet Cleaner # F7410-900

"I did some research online and the recurrent theme was a bad turbine assembly. Fortunately I was able to fix this myself which took about 2 hours (some reading) and little effort. The problem was with the turbine which is fairly simple and had a bearing that had rusted and froze up. Removing the cover proved to be more difficult than fixing the stuck bearing. This was mostly due to figuring out the correct screws to remove and finally discovering that the back of the cover (over the wheels) is not secured by fasteners but by pegs that "pop" out.

Once I had the brush assembly and Cover removed the turbine came out with the removal of some obvious screws and gently pulling the hoses from the assembly. After carefully opening the assembly housing I discovered the bearing problem and with a little lubrication and some new grease had it working in short order. Putting everything back together was simple as well."


this worked for me. although once i got in i just had to mess around with the gears and loosen them up. getting in was the hard part soo here you go peoples.

take off tanks

unscrew 6 screws fom underneath machine. look carefully

just underneath where the dirty tank goes right by the part that sucks everything up is a screw. unscrew it

pop off the switch for your spin scrub mode. it pops right back on.

make sure your locks for the tank are turned in

then the back just pops off. you might have to give it a good tug. there are no screws although it maight look like there is.

then pull off the grey part.

once inside it is pretty easy.

but if you have any questionbs email at lostnhisblueyes@aol.com

i took off so many more screws than i needed to to get this figured out so dont do that.

Posted on Apr 03, 2009

  • 1 Answer

SOURCE: Hoover steam carpet cleaner brushes dont spin

There is a plastic cover over the spinner indicator. If you take the plastic cover off there is also a little filter in that area (almost like the spinner is on the floor and the filter is on the wall). If you clean this filter it may start working again. I had the same problem before and it worked for me. I found the info in the user's manual for my model. Hope this works for you as well.

Posted on Sep 04, 2009

  • 1 Answer

SOURCE: agitator brushes wont turn even after cleaning

the brushes will not turn even wen the switch is turned on

Posted on Sep 06, 2009

VacuumRepair
  • 438 Answers

SOURCE: why don't the brushes go round on my Hoover carpet cleaner

HI There,

Here's a link to a Fixya repair solution that I recently did on this exact problem. It's actually a fairly common problem. The second link is to another solution that will walk you through step by step how to replace the turbine assembly if you find out this is what the problem is.

How to Diagnosis a Hoover steamvac spinscrub brushes stop spinning:
http://www.fixya.com/support/t4286338-hooverspin_scrub_brushes_always_stop

How to replace the Brush Turbine Gear if you find out this is what has gone bad:
http://www.fixya.com/support/r4530769-diagnosis_fix_hoover_steamvacs_when

If you need to purchase a new spinscrub brush block, here's a direct link to the exact brush block that's used in your model:
Hoover SteamVac Brush Block - 5 Brushes Part # 48437022

If you have any follow up questions, please don't hesitate to ask them by using the comment form here on the Fixya repair page.

Thank you,

Chris Jones
GoVacuum.com

Posted on May 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hoover max extract brushes wont spin


Check that the brushes are not jammed up with hair and fluff.
Remove the brush from the housing and clean throughly including the bushes/inserts and belt
Hope that helps

Feb 09, 2014 | Hoover Platinum Carpet Cleaner With...

2 Answers

On hoover steam carpet cleaner, the brushes do not rotate on low or high settings.


Follow these steps if the Brushes Fail to Spin
•If the brushes on your Hoover carpet cleaner fail to spin, there may be a problem---some sort of blockage---with the suction or with the belt that turns the brushes.
Turn the Hoover carpet cleaner over, and inspect the brush area. Debris, strings, or pet hair may be tangled in the rollers, keeping them from turning. Use a pair of scissors to cut away any obstructions in this area. Flip the Hoover carpet cleaner back over, and turn it on to see if cleaning the rollers has solved the problem.
To check the belt, turn the Hoover carpet cleaner over, and remove the bottom plate screw with a Phillips head screwdriver. Investigate the belt area to see if it is broken or has somehow slipped off. If it is broken, you can order a part from Hoover.com or from many of the other online parts stores.
When the belt arrives, simply slide it on in place of the broken belt, reattach the bottom plate and turn the Hoover carpet cleaner right-side up. Turn it on to test your solution.

Sep 03, 2010 | Hoover SteamVac F5914-900 SpinScrub...

1 Answer

I have a Hoover carpet cleaner - Model # f7441-980. My brushes do not rotate.


There is a plastic piece on the back of the block brush (spin scrubbers) these wear out or break. You may need to replace the block brush. You can find the parts and a schematic below follow the link. Please don't forget to give positive feedback.

F7441 Link

http://www.usavacuum.com/Hoover-Steamvac-s/109.htm

Jan 29, 2010 | Hoover SteamVac F5914-900 SpinScrub...

1 Answer

My brushes on my hoover steamvac all terrain carpet and hard floor cleaner will not spin what do i do


I am not sure if you have the F7222 or F7452 all terran. There is a plastic piece on the back of the block brush (spin scrubbers) these wear out or break. You may need to replace the block brush. You can find the parts below follow the link. Please don't forget to give positive feedback.

Hoover F7XXX Link

http://www.usavacuum.com/Hoover-Steamvac-s/107.htm


Jan 29, 2010 | Hoover STEAMVAC VACUUM Vacuum

1 Answer

Hoover steam vac deluxe - no suction and the scrubbers aren't spinning uless you tilt off the floor.


I would suspect that your turbine assembly bearings need to be replaced. also check for debris inside the brush assembly. check the intake filter under the front clear cover. verify the recovery tank lid is on securely, as well as the foam filter on the tank lid is clean.

Oct 10, 2009 | Hoover SteamVac Carpet/Upholstery Deep...

1 Answer

My hoover carpet scrubber the brushes won


(1) Remove the brush block and assure the presence of the square drive pin on top of one brush. It should be about 1/4 inch square, two inches long to connect o the drive mechanism.

(2) Remove and clean the filter screen from the base, behind the brushes. Squeeze the two red tabs together, and pull down from the base. Clean the hiar/debris from the screen.

(3) Assure the Brush Speed knob on the hood is NOT set to the OFF position.

Aug 30, 2009 | Hoover SteamVac Carpet/Upholstery Deep...

1 Answer

We have a 2x brushes bissell carpet scrubber. Do


Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101
x

Aug 29, 2009 | Bissell 9500 ProHeat 2X CleanShot Upright...

2 Answers

I got new belts but the brush wont turn


Make sure the vacuum is on the carpet setting..the brush won't turn on the hard floor setting..

Dec 16, 2008 | Hoover U6437-900 / U6439-900 Windtunnel...

1 Answer

Belt replacement Hoover carpet cleaner


Hoover steamvacs don't use belts. If the brushes are not turning, pull the brush block out, turn the machine on and see if the square hole where the brush block was, is turning. If not then the turbine is bad. Sometimes you can take the turbine apart and clean it out. most times I have found , replace it.

May 24, 2008 | Hoover SteamVac Carpet/Upholstery Deep...

Not finding what you are looking for?
Hoover U6434-900 Bagged Upright Vacuum Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18389 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Brad Brown

Level 3 Expert

15451 Answers

Are you a Hoover Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...