Question about Maytag MAH2400A Front Load Washer

1 Answer

F3E2 Error Code Only When Clothes Are in the washer

I was receiving an F3E2 Error code which states something to do with the water temperature sensor. I got a new water temperature sensor and replaced. Now the washer will run fine without any clothes in the tub but when I put clothes in the error code immediately comes back up and will not run. What else should I be looking for as a problem?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Maytag Master
  • 15,557 Answers

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 163 Answers

SOURCE: Washer spins but not enough to extract water from clothes or tub.

it sound to me to be the water pump, with all the water in the tub, the machine dont spin ok, and the water is extracted by centifugal force, not by pumping as it should be, call a tech, this is a hard job for regular people..good luck

Posted on Aug 10, 2006

  • 1 Answer

SOURCE: Amana front load washer error code 5d

5d means you're using too much detergent.

Posted on Jul 22, 2008

  • 1 Answer

SOURCE: Maytag Neptune Error COde "nd"

I had the exact same problem. nd code (no-drain) at the end of the cycle and when I opened the door the machine was still full of water. I took the back panel off the washer and disconnected the drain hose from the pump. (You're going to get quite a bit of water gushing out at you so be prepared with towels or a shop vac.) At this point you should see a little rubber disc over the end of the section you just exposed on the pump. This is a little drain flap. Just lift it up and you should be able to see into the pump a little bit. At this point I poked around in there with my finger and found a hair pin stuck in the pump! I wasn't able to get it out from this end of the pump so I disconnected the big rubber boot which connects the wash drum to the pump. Then I was able to twist the pump (counter clock-wise) and release it from the washer base. I didn't have to disconnect any wires and was then able to see into the other side of the pump and pull the hairpin out. Put everything back together and it's worked fine ever since. I've never even looked inside a washing machine before but it really was really fairly simple. Now my husband really does think I'm a domestic Goddess. I said he should take me out to dinner with the money we saved on a service call!!

Posted on Mar 18, 2009

  • 1 Answer

SOURCE: Maytag Neptune Error COde "nd"

This is now the 3rd time this has happened. The 1st 2 times it cost me ~$100 to have a technician come in and fix.

This time, I did it easily. For my Maytag Neptune washer, I removed the back panel (2 screws). On the bottom tray is the water discharge pump. On the output side of the pump there is a small cavity under the rubber flapper where a nickle fits perfectly. I removed the nickle, reattached the output drain line. started it up ...

and viola! the problem solved.

Posted on Jun 28, 2009

FAV6800AWDIY
  • 526 Answers

SOURCE: Unbalance Issue with my washer model FAV6800AWW.

Hi 2pleach

If you are taken dC/uC errors I think you have to drop the clutch out again and see if you can clean and Re-Lube the One-Way Roller clutches/bearing. I wonder if you have a slight tub seal leak causing this issue to reoccur. Did you follow my clutch maintenance/replacement post Clutch repair post on this site? As you know I’m a DIY’er/owner as you. You did the right troubleshooting with the TDS check.


I have posted solutions under dh1200s and FAV6800AWDIY. I feel I have 50+ machine saves $1k original cost I think between this site, FIXITNOW.COM, APPLIANCEJUNK.com Appliance repairparts.com forum. I go by dh1200s on those forums. The bulk of this FAV6800AW/FAV9800A machine owners flock to this forum…..I should get some consulting $fee$....:) but I do it for nada just trying help owners like myself not junk a $1000 machine.

Regarding the struts see this post. I feel if you are going to chime in on a fix you should know the subject matter. If the tub sets level and returns to normal after the TDS checks you are good to go…..not rocket science just common sense and good old fashion troubleshooting. A lost art among some repair folks or they never had it to begin with.

You are a very savvy DIY’er let’s drop the clutch out again. Please look at this post I show how to test if the One-Way Roller clutches are not locking up in the CCWSpin cycle direction. Don’t get distracted with misinformed info about the front struts.

I can give you phone support if necessary just let me know what I can do to help…. I push no snake oil fixes….:)…Rich I go by *D*i*c*k* but this BS board blanks it out as a nasty .

Posted on Jan 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have Duet waSher, model #WFW9151YW00. I have an error code F3E2. Thought it was the temperature sensor, which we just replaced, but still getting the same error code. Now what?


This could be a wiring fault between the water temperature sensor and the control unit. Make sure that the connectors are properly seated at both sides. Sometimes, one section of the wiring can get pinched and one of the wires in that harness could break. Check that all of the wires in the harness have continuity; the wiring may need to be replaced. Clean out the trap before the discharge pump just in case the error is from a different part of the washer's system.

I hope this helps.

Cindy Wells

Dec 01, 2016 | Washing Machines

1 Answer

What does error code F 24 mean on a whirlpool clothes washer duet front load


The "F24" fault code indicates a water temperature sensor error. The temperature sensor could be faulty; the wire connection may have vibrated loose or off the sensor or a possible heater or control board failure.

Jul 13, 2015 | Whirlpool duet Washing Machines

1 Answer

I was receiving an F3E2 Error code which states something to do with the water temperature sensor. I got a new water temperature sensor and replaced. Now the washer will run fine without any clothes in the...


WATER TEMPERATURE SENSOR ERROR
If the water temperature sensor (NTC) value is out of range (23°F to 217°F
[-5°C to 103°C]) during the water-heating step of the WASH cycle.
Possible Causes/Procedure
- Unplug washer or disconnect power.
- Make sure that connections to water heater & CCU (TH2 & HE2 cavities)
connectors are not broken or with wires detached, and that connector internal
pins are visible.
- Check continuity from the water heater sensor (black wires) to CCU
(TH2 cavity) connector.
- If the continuity diagnosis failed, the Main Harness must be replaced.
- Check the resistance of heating element.
- Check the resistance of the water sensor.
- Plug in washer or reconnect power.
- Verify the washer operation by running the Diagnostic Test cycle.
- After the diagnostic test has finished, unplug washer or disconnect
power and wait for 15 seconds.
Water Temperature Sensor
1. Unplug washer or disconnect power.
2. Disconnect the wire harness from the water temperature
sensor and measure the resistance of the sensor. Use the
following table. An abnormal condition is an open circuit =
infinity; Water Temperature Sensor must be replaced.
Temperature Results
32°F (0°C) 35.9k ?
86°F (30°C) 9.7k ?
104°F (40°C) 6.6k ?
122°F (50°C) 4.6k ?
140°F (60°C) 3.2k ?
158°F (71°C) 2.3k ?
203°F (96°C) 1k ?

Nov 25, 2014 | Washing Machines

1 Answer

When i used my washer after 3-4 mins f3 e2 maytag front load washer , changed ntc but still same


I am sorry to hear that you have error code F3E2. I know how upsetting error codes can be. I see here that for your Maytag washer, error F3E2 means there is a water temperature sensor error. Below is to test the error
WATER TEMPERATURE SENSOR ERROR:
1. If the water temperature sensor valve is out of range (23 degrees to 217 degrees F or -5 to 103 degree C) during the water-heating step of the WASH cycle.
Possible causes/procedures
a. Unplug washer or disconnect power
b. Make sure that connections to water heater and CCU (TH2 & HE2 cavities) connectors are not broken or with wires detached, and that connector internal pins are visible.
c. Check continuity from the water heater sensor (black wires to CCU (TH2 cavity) Connector.
d. If the continuity diagnosis failed, the Main Harness must be replaced.
e. Check the resistance of the heating element.
f. Check the resistance of the water sensor.
g. Plug in the washer or reconnect power.
h. Verify the washer operation by running the Diagnostic test.
i. After the diagnostic test has finished, unplug washer or disconnect power and wait for 15 seconds.
Below is the diagnostic test. I have it in two halves so you can read it best that way.
If you will submit your model number I will be able to help you further.

Nov 25, 2014 | Maytag Washing Machines

1 Answer

What does error code f5 mean?


The F5 error code indicates a water temperature problem. The control board circuit is not recognizing a resistance change in the water temperature sensor.

You most likely have a loose connection at the tub sensor , or a bad heater.

Read more: http://forum.appliancepartspros.com/washer-repair/244131-error-code-f5-model-11045087404-kenmore-elite-residential-washer.html#ixzz34ySdUUeZ
http://forum.appliancepartspros.com

Jun 14, 2014 | Kenmore HE2 Plus Front Load Washer

1 Answer

Whirlpool washer model wfw9150ww01fault code f3e2


F3 E2 mean that your temperature sensor is shorted. You'll need to replace the temperature sensor which is mounted to the very back left corner of the washer tub. That means you'll need to pull the washer out and remove the back panel to see it. Here is the part to order. Here is a diagram of the unit. The sensor is number 23 on the diagram.


Jan 20, 2013 | Whirlpool Washing Machines

1 Answer

Kenmore Elite smartwash QuietPak9 F H error code


Press the Pause/Cancel button twice to clear the display then check if water is introduced into the machine. Drain the water from the machine by selecting Drain and Spin then pressing the Start button for one second. Empty the machine after the water is completely drained.

Start a new cycle with Hot/Cold water temperature and check how long before the error code appears after the cycle is started. When the code appears, press the Pause/Cancel button to clear the display then check again if water is introduced into the machine.

The pressure switch is not tripping and must be replaced if the error code appears about 8 minutes after the cycle is started and about 40 liters of water is introduced into the machine.

The flow meter is not working if the error code appears less than a minute after the cycle is started and about 3 liters of water is introduced into the machine.

The valve solenoids may not be working or the levers are stuck if the error code appears less than a minute after the cycle is started and no water is introduced into the machine.

Let us know which case above is observed for specific troubleshooting and repair guide.

Mar 09, 2010 | Kenmore Elite 45986 Front Load Washer

1 Answer

Screen displays error code f3e2


This code means "BAKE/BROIL range over temperature"
Problem is in either temperature sensor or the control board. Check the temp sensor and wiring from it to the control board first (connector #3, contacts 8 and 10, violet wires) . At room temperature the temp sensor resistance should be around 1080 Ohms. Also check temp sensor for short to ground. If no problems found with the sensor - replace control board.
OBTW - for the broil problem - check the fuse inline with the broil element (continuity between Conn #2, wire 1, blue and conn #4, wire 3, red). It should read several ohms. Good luck!

Oct 12, 2009 | Whirlpool RF462LXSB Electric Range

1 Answer

He2plus does not drain and spin


code F24
WATER TEMPERATURE SENSOR ERROR

next information is only for the TECHNICION

If the water temperature sensor NTC value is out of range (23 F to 217 F to 103F C) during the water-heating step of the WASHcycle.
NOTE:To find corrrect Ohm reading refer to the water temperature sensor in TECHNICION ONLY section.
Possible couse/Procedure
1.- Unplug washer or disconect power.
2.*check the water senser and conection to it.
3.-check resistence of heating element, if present on this model(abnormal=indifinity)
4.-refer to the water Temperature Sensor section

Am sorry but F7 error code is not in the information system.


"Was this helpful?"

May 11, 2009 | Kenmore HE2 Plus Front Load Washer

Not finding what you are looking for?
Maytag MAH2400A Front Load Washer Logo

235 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

587 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...