Question about Radio Communications

Open Question

I have a brand new Kenwood pro talk Tk2402V 9 out

I have a brand new Kenwood pro talk Tk2402V 9 out of 16channels programmed I need the 9 reprogrammed and the remaining 16 programming how much and where?its vhf and narrowband capable.

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: how to program a motorola gp328 vhf 2 way radio?

i have program kit and software i need program for emergency siren what i have to do

Posted on May 10, 2009

  • 1654 Answers


Contact Ritron at 800-872-1872

Posted on Jul 27, 2009

  • 12 Answers

SOURCE: I need the IC-F11/S to talk to my CP100 (vhf) model

First you will need to find out what freq and tone your Moto is on then program you Icom with software Icom CS-F11. Software can be purchased online. Carl

Posted on Aug 10, 2009

  • 1654 Answers


The HT1000 change to narrowband depends on the generation of HT1000 you have. If a model made since the year 2000 (or so) it should be able to be either programmed or converted. If it is a pre-2000 (or so) model, it will not be capable.

Programmable narrowband can be done by any authorized Motorola dealer. Conversion to narrowband requires components in the radio to be changed by a qualified electronics technician using approved methods, not necessarily available at every dealer.

Check with your local Motorola dealer to see if they can help you with programming or conversion. If not, repost your model number in a question here on FixYa and we will let you know which scenerio you are facing and give you some suggestions on where you can have it done.

Best regards.

Posted on Apr 22, 2010

  • 1654 Answers

SOURCE: narrowbanding-can you look up serial number to see if capable?

Yes, it can be looked up by either method, serial number or product number. In a Motorola serial number the first 3 numbers will tell the kind of radio and the next 3 letters will tell where and when it was manufactured.

Best regards.

Posted on May 26, 2010

Testimonial: "This is great information! Thank you so much! Anna"

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do i reset a kenwood tk3160 to the default settings.


I scoured your KENWOOD TK3160 Users Manual and a RESET process is NOT shown at all!? Find the link below...

They DO mention Programming Software and THAT may be your BEST solution?

You also want to gracefully reprogram your transceiver and SOFTWARE is your best choice for that too!

Your programming cable is about $5.35 FOR TWO on eBay... I KNOW!...


2xUSB Programming Cable Adapter for Kenwood TK 3102 TK 3107 TK 3118 TK...

Dec 02, 2017 | Kenwood Radio Communications

1 Answer

When I turn it on, why does it indicate confirm?

Something is wrong with the programming. It does not happen often, but it happens. Reprogram it, or find the factory reset in the manual. If that does not work, the radio memory chip is defective. Reset is your best option.

Aug 28, 2015 | Kenwood Tk 3300 Protalk Uhf Two Way Radio...

1 Answer

Kenwood TK-3302U16P ver 2

Search at internet by writting TK-3302U16 programming software

Feb 14, 2014 | Kenwood TK-3302U16P 450-470 MHz UHF 4 Watt...

1 Answer

How do i change the channel?

Programming a Frequency to a
Selected Channel:
1. Press and hold down the Push-To-Talk
button while turning the radio on, wait for
approximately 5 seconds then release the
Push-To-Talk button.
2. Use Scroll button to select one of the 8
frequencies. Figure 16.
3. On a Spirit GT+, press the Monitor button.
4. The current channel will flash, press scroll
button to change channel.
5. After the second channel is selected, press Monitor button again, current
frequency for second channel will flash. Figure 16.
6. Use Scroll button to select new frequency.
Exit Programming Mode - 3 Ways
1. Press Push-To-Talk to exit completely.
2. Allow the Menu time to expire (10 seconds).
3. Press Menu button to go to code programming.

Here is a link to the user manual:

Jun 25, 2009 | Motorola Spirit GT Pro (2 Channels) 2-Way...

2 Answers

My new kenwood protalk tk 3130 wont talk to me old 3130

Look at the user manuals for both radios and compare the frequency assignment for each channel. find the ones that match and program the radios to talk to each other.


Nov 18, 2008 | Kenwood ProTalk XLS TK-3131 (15 Channels)...

1 Answer

Remote will not program

See this website. It worked for me and I've never soldered before.

Sep 02, 2008 | Kenwood VR-507 Receiver

2 Answers

My new used kenwood tk370

If you have not resolved this problem yet. I fear that your radios may have a CPU problem. in any case here is a URL that explains how to program your radios.


Jul 31, 2008 | Kenwood Radio TK 260 360 270 370 2100 3100...

Not finding what you are looking for?
Radio Communications Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Radio Communications Experts


Level 3 Expert

1654 Answers

Brad Brown

Level 3 Expert

17326 Answers


Level 3 Expert

80531 Answers

Are you a Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides