Question about Televison & Video
Tv has sound but no picture, tried dvd cumes up but very faint and red but no sound
First check its main power supply regualtor board's output voltages. If any of these multiple voltages become low than normal, this type of fault can occur. If you are not familiar with electronics, do not attempt to repair. Whether you suffer fatal electric shock. Instead, contact any experienced service technician, or the nearest service center.
Posted on Apr 25, 2013
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: No picture, sound ok
I have a similar issue. Sometimes the entire screen goes black and sometimes only one-half - either the top or bottom half goes black. The only solution we have found is to gently tap the TV (usually the front side) and the picture will come back for awhile. It almost seems heat related as it only goes out after the first 10 minutes of use. There must be a fix to this.
Posted on Sep 28, 2008
When you tune to a station and get sound I presume the screen is black so do the following.
Place a bright flashlight against the screen. Look for an image around the edge of the flashlight.
If you see an image the problem is probably one of three causes.
1) Power to the inverter board is bad.
2) Inverter board has failed.
3) The CCFT(cold cathode fluorescent light) are dead.
Someone knowledgeable in electronics can diagnosis it.
Posted on Mar 15, 2009
Unfortunately, what you're describing is a repair issue. You won't be able to address the problem with troubleshooting. There is a part inside the TV that needs to be replaced. If you're under warranty, this will cost you nothing. If you're not under warranty the cost will likely be a minimum of $200 parts and labor. However, be warned that the cost could be considerably higher.
I hope I've provided you useful assistance and that this information allows you to make an informed decision as to how to proceed from here. Please be sure to vote on my response. I hope I've earned a good rating from you today.
Please post a comment if you need additional assistance so that I can help you further
Posted on Jul 22, 2009
Tips for a great answer:
Jan 26, 2016 | Samsung Televison & Video
Dec 15, 2015 | Televison & Video
Jul 20, 2015 | Televison & Video
Jun 15, 2013 | Televison & Video
Feb 03, 2013 | Televison & Video
Oct 06, 2012 | Televison & Video
Jan 12, 2018 | Philips 32PF9830 32 in. HD-Ready LCD...
137 221 371 218 220 101 236 100 033 245
1* Select any channel on the TV.
2* Point your Sky+ remote control away from the TV and press the tv button.
3* Press and hold down the Select and red buttons simultaneously on the Sky+ remote control until the red light at the top of the Sky+ remote control flashes twice.
4. Input the 3 digit number from the Sky+ remote control codes then press the Select button. The red light at the top of the Sky+ remote control should flash twice.
5* Point the Sky+ remote control at the TV and try the volume button.
If this works try the other TV functions.
If these work then the correct code has been selected.
It's important to note that not all TV functions will be supported by the Sky+ remote control e.g. Picture in Picture.
If all functions do not work correctly, then repeat steps 1 - 3 and work through all the relevant 3 digit numbers from the Sky+ remote control codes, until you find the code which supports all or as many of the TV functions as possible.
Jul 10, 2011 | Televison & Video
Dec 08, 2010 | Televison & Video
Jul 22, 2018 | Sanyo Televison & Video
Jul 22, 2018 | Televison & Video
192 people viewed this question
Usually answered in minutes!