Question about Kohler Riverbath Quadrangle Whirlpool w/ Integral Fill - K-1360-H2/Color=Bl

1 Answer

Heater doesn't work correctly

My heater does not work on my riverbath quadrangle by kohler. If I turn off the power it will work for one or two cycles then no longer until I turn off power again. I have replaced Heater, and computers the motors sit on. Kohler is no help. Any ideas?

Thanks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 234 Answers

I think the pump is going out on reset or hi limit

Posted on Mar 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rheen PVW50 Hot Water Heater Making Buzzing Noise and Doesn't Light


Why is it always Rheem problems?
Every water heater problem is Rheem.
And Rheem doesn't post any service manuals, like the other two big manufacturers, AO Smith-American, and Bradford White.

Copy following link for troubleshoot by gas control valve.
http://waterheatertimer.org/How-to-troubleshoot-gas-water-heater.html#intellivent

Scroll up and find pressure switch heading among links.

You can install gas control valve yourself.
http://waterheatertimer.org/pdf/How-to-replace-water-heater-gas-valve.pdf

Sep 06, 2012 | Rheem Water Heaters

1 Answer

We have a ge electric water heater - last night we set a new jug of detergent on top of it over the electric plate on the top of the unit - it had a hole ( small leak) in the bottom - it leaked all night...


You flooded water heater wiring compartment with detergent, and the wires were shorting so you turned off power and cleaned detergent. Now water heater doesn't work.

1) The heat from shorting might have tripped ECO reset button.
Open top cover on water heater, and push in red reset ECO button.
http://waterheatertimer.org/images/Jly-022-thermostat2-175.jpg
Be sure to re-install insulation and cover.

Other steps:
2) Turn off power. Remove wire nuts. Cut off copper ends of wire, and re-strip each wire so fresh copper shows. Make sure no detergent is on the copper. Use new wire nuts and twist very tight against copper wire.
3) Cut back burned ground wire. Remove ground screw and clean thoroughly. And then reattach clean copper to ground screw.
4) Turn power back on.

5) If water heater still does not work, then test across top two screws on upper thermostat for correct voltage.
http://waterheatertimer.org/images/Jly-022-thermostat3-175.jpg
http://waterheatertimer.org/Test-electricity-to-water-heater.html

Add a comment for more help.

Take a moment and rate answer for accuracy:
And take advantage of fixya expert assistance live.
For a price, expert works with you while you work on water heater or any do-it-yourself project.
Fixya is always less expensive than a service call.

Sep 12, 2011 | General Electric Water Heaters

1 Answer

I have a 1991 40 gl and it fell through the floor which is like 2 ft off the ground. turned the water off and replaced the pipes it has its own lever type power supply with the screw in fuses 30 amp (2) of...


You have 2 problems with several possible causes:
You have 10-year-old electric water heater that was reinstalled after falling down, and doesn't heat the water.
And you have no hot or cold water pressure, and no pipes are leaking.

1) First problem is lack of water pressure throughout house.
Turn on outdoor spigot nearest to water meter.
This spigot will tell you if problem is inside the house or between the house and meter.
If spigot runs full force, then you probably have clogged pipe where water heater connects to main cold line, or the main shut off valve got clogged with sediment that broke off inside the pipe when you were working on water heater.
Open and close shut off valve to see if that helps. Then disassemble pipes and track back the problem. Put pressure gauge on water heater drain valve to watch pressure drop when turning on indoor faucet.
Read following information:
http://waterheatertimer.org/Low-hot-water-pressure.html

Water heater doesn't work:
Test across wires at top of heater to see if you are getting correct voltage:
If tank is receiving correct voltage, then no hot water puts suspicion on upper element or upper thermostat, or both.
Open following link for electric water heater troubleshoot steps:
http://waterheatertimer.org/How-to-troubleshoot-electric-water-heater.html

Jul 30, 2011 | RELIANCE ELECTRIC WATER HEATER

1 Answer

Can I add a inline heater to a Kohler whirlpool 1164?


In looking at the spec sheet for this model, it appears that a heater is already installed at the factory. See this link:
http://www.us.kohler.com/onlinecatalog/detail.jsp?item=9737602&prod_num=1164-H&module=Bathing&frm=null

If the whirlpool isn't heating, the power to the heater, thermostat, and the heater itself should be checked.

Apr 08, 2010 | Kohler Sunward K-1164-H-96 Biscuit 6 Feet...

2 Answers

Bosch 2400E-NG output temp fluctuates


This is a great heater. It is however crucial that it be installed to every detail of the manual. If there is trouble send pictures to Bosch tankless you can call 1-800-283-3787 ask for Bosch Tech support or go to boschhotwater.com click find a contractor and call the closest Bosch Service Provider most will travel.

Mar 04, 2010 | Bosch AquaStar 2400ES-NG

1 Answer

Kohler sok overflowing tub motor will not run theres power and green light indicates it should work


maybe the motor is not working any more, if you have curent to the motor but not thru the motor you need to get a motor

Apr 03, 2009 | Kohler K-1188-C1-0 sok overflowing bath...

1 Answer

The water jet pump wont turn off or sometimes turns on by itself


go online to kohler and they will send you out a new switch,, it isn't that hard to install, this will solve your problem and I think if you tell them it was put in not to long ago they will send it for free

Apr 03, 2009 | Kohler Devonshire 5ft Drop-In Bubble...

1 Answer

When we press the "on" switch in or Kohler whirlpool tub it trips the wall switch. I changed the wall plug and it still trips when trying to turn it on. It has always worked fine. Any suggestions..


Remove the GFCI WALL OUTLET and try connecting those wires together blk/blk..wht 2 wht...ground to ground and then see if tub will stay on, if not suggest put back together and call qulified whirl pool tech to find short in pump motor.

Please rate. Thank you. jj505

Mar 28, 2009 | Kohler Synchrony K-1192-LH-0 White 5 Feet...

Not finding what you are looking for?
Kohler Riverbath Quadrangle Whirlpool w/ Integral Fill - K-1360-H2/Color=Bl Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kohler Water Heaters Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Todd B

Level 3 Expert

571 Answers

Gene Haynes

Level 3 Expert

5080 Answers

Are you a Kohler Water Heater Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...