Question about Bosch Nexxt Premium WFMC6400UC Front Load Washer

1 Answer

Washer will not complete the cycle

Model: WFMC 2100UC/01 WILL NOT COMPLETE THE WASH CYCLE. IT STOPS THEN UNLOCK THE DOOR.

Posted by on

  • mjand Mar 18, 2009

    My bosch washing machine will not complete the cycle. You would think that after spending thousand of dollars on bosch products they would have a better customer help or parts. I guess thier repair men must have a corner on the market, American capitalism at its best :-(!

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,294 Answers

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washer wont complete cycle


Sound like the control board is bad

Jul 25, 2012 | AEG Lavamat 72640 Front Load Washer

1 Answer

Whirlpool duet washer door will not unlock or complete the cycle


Wait at least three minutes after the end of the cycle before attempting to unlock your Whirlpool washer. The door will not unlock until the motor speed equals 0 and 180 seconds have elapsed since the motor control unit received the "Stop" command. If the water in the washer is warmer than 122 degrees Fahrenheit or the water level is set higher than Wool, Delicate or Hand Wash, the washer must drain before the door latch will unlock 2 Hold down the "Control Lock" button on your Whirlpool washer for three seconds at the end of the washing cycle. Listen, and when you hear the unlatching sound, the door should open.3 If your Whirlpool washer did not unlock at the end of Step 1, press and hold the "End of Cycle" button for five seconds to manually reset your washing machine.4 Unplug your Whirlpool washer and leave it unplugged for 45 minutes. After 45 minutes, plug your washer back in. The washer's programming should be reset and the door should open.5 Manually unlock the door of your Whirlpool washing machine. Make sure to unplug the appliance before completing the manual unlock. Use a screwdriver to remove the metal strip, called the toe panel, at the bottom of the washing machine. Once you've removed the toe panel, reach up inside the front panel of the washer and feel around for the door latch. Locate the tear-drop shaped tab at the bottom of the door latch and pull it gently. When you hear a click, the door should open.
  • Oct 13, 2011 | Whirlpool Washing Machines

    1 Answer

    Need instructions for moving -- have four bolts!


    Hi.

    Here the full set of instructions for the model Bosch WFMC 3200 posted in title:

    WFMC3200UC/01 Manual 1

    WFMC3200UC/01 Manual 2

    Here repair manual available for $9.95.

    Regards.

    Ginko

    Jun 07, 2011 | Bosch WFMC 3200 Front Load Washer

    1 Answer

    I load the clothes into the washing machine, I turn it on select cycle and the door locks and will NOT unlock. The door will however unlock after the cycle is finished.


    Not sure if you're unable to open the door AFTER you stop the cycle. That may be normal operation as a safety measure (won't open until after your cycle has completed). However, if your model DOES allow for opening the door during cycle operations then your electronic door lock may be defective.

    Mar 08, 2011 | LG WM-2277HW Front Load Washer

    1 Answer

    I have a Bosch Nexxt washer, model number WFMC 32000C/01. Yesterday I noticed the fabric softener was still in the dispenser after the cycle was completed. I cleaned out the dispenser and ran another...


    Could be the fine holes in upper dispenser are blocked. Remove soap dispenser drawer and use a washing up brush to clean upper dispenser, replace drawer & test. If not could be upper dispenser or inlet valve.

    Jan 10, 2011 | Bosch Washing Machines

    1 Answer

    Error E;04


    Located front down on right hand side. Remove cover gain access to water pump.

    Jan 31, 2009 | Bosch Nexxt Premium WFMC6400UC Front Load...

    1 Answer

    Have a Bosch WFMC 3200UC and gives a E04 error.


    In order to unlock the door on this machine you must first turn the cycle knob to a cycle that was different than the one you were on. The machine should then reset and the door should unlock.

    Jul 13, 2008 | Bosch Nexxt 500 WFMC3301 Front Load Washer

    1 Answer

    Door locked,wont spin or drain.


    humming noise suggests a foreign object in the pump. crack open filter and drain water into a shallow tray. repeat till empty. remove filter completely and clean it. check if something stuck in pump impellor. this should be visible by looking into the filter hole

    Jun 22, 2007 | Bosch WFMC 3200 Front Load Washer

    Not finding what you are looking for?
    Bosch Nexxt Premium WFMC6400UC Front Load Washer Logo

    296 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Bosch Washing Machines Experts

    Tim Whalen

    Level 3 Expert

    3056 Answers

    Richard Roth
    Richard Roth

    Level 3 Expert

    9472 Answers

    yadayada
    yadayada

    Level 3 Expert

    60667 Answers

    Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...