Question about GE Profile DPSB613G Gas Dryer

Open Question

Black marks from dryer

My GE Profile dryer which is only about 5 years young is now leaving black streaky marks on my white sheets. I've discovered this only happens on my sheets since they are the only thing I dry on high. I've never seen the marks on any other light colored loads that I do on medium heat. And I could never figure out where the marks were coming from. And regular Shout, laundry soaps, bleach, etc. did nothing to remove them. I had to do two back to back dryer loads on high both full of sheets after company and after the second load I noticed some black residue on one of the upper corners of the door which opens left to right, with this residue on the top inside right of the door. I wiped it off with a finger first and it's more powdery than oily. Reminded me of graphite from a pencil. I took the used dryer sheet and wiped the rest off the door and then looked at the dryer in the corresponding location. My dryer model # DPSR610EG0WT has white plastic edging between the inside of the door and the drum. This powdery substance is coming from both sides of this plastic edging on the top exactly where I saw it on the door. I crammed the dryer sheet in both sides inside and outside of this edging and wiped around it and it was BLACK from this stuff!! I tried some Carbona grease cleaner on my sheets and I thnk that worked for the most part to remove the marks on my sheets. But now I have to rewash and redry them all over again. What is this stuff and what do we have to do to stop it from happening? My husband is a master mechanic from birth (even though he has a white collar desk job) and can repair and fix anything. Now he's listening to me since I told him I'll start drying his shirts on high! Please advise!

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
FRANKSFIXIT
  • 72 Answers

SOURCE: Squeeking noise

Here's a possible troubleshooting fix I just sent to someone else that quite possibly has the same problem you have there now.

Hope it helps you out as well, as it is a bit long, but I'll post the whole reply I sent them and you can use whatever parts of it that will work for you.

Hi,

My name is Frank...

Regarding your possibly broken dryer.

I'm hoping that this info below helps you out even though I know I won't be able to repair/fix your dryer myself personally. Reason why - I'll explain further down.

I've repaired a few gas dryers & washing machines as well in my time. I can honestly say that I'm as close to being an expert as they come - esp when it comes to making repairs on existing dryer parts that can no longer be purchased as they are either obsolete, or way over-priced.

This is what I do for a semi-retired hobby, and sideline self-employed FIX-IT business. Named appropriately - FRANK'S FIX-IT SHOP. It's only an online fix it at present. Keeps me busy instead of being bored to death.

Electric clothes dryers are typically made the same as gas dryers - as to the mechanical drum part. Only thing different in a gas unit is the 110VAC electrical igniter or element, and the gas delivery system that provides the drying heat to the dryer itself.

All else is basically the same...

In an electric clothes dryer all the power comes from the 220VAC source as to the heating element, etc. The mechanical parts are typically the same as that of a gas dryer.

Having said this - the problem with your dryer can only have one of possibly 2 things wrong with it - seeings it's no doubt 220VAC totally electric, unless you actually have gas where you are there, which is rare in Florida these days!

If after you start the drying cycle you quickly open the dryer door, and you notice the drum is actually rotating - until there is the loss of electric power via a safety door switch that kills electric power to the drum motor activity - then there is NOT a problem with a broken drum belt.

If your dryer is older then say 10-15 years, and you really use it alot - then maybe there's a possibility of a broken drum belt (cost is around $10-15 for a new belt part depending on model - usually - and that does not include labor to install it).

Usually you'll hear the motor whining, but no drum 'noise' or movement. Dead giveaway as to a broken belt.

I had replaced 2 belts and 1 IDLER wheel on my own 30+ year old gas Kenmore dryer before selling it, and then picked up a more recent newer model GE washer & gas dryer that someone was just giving away for free. My 30+ year old Kenmore washer had just died on me at the same time is why I upgraded. Can't pass up a great freebie deal like that everyday! Never had to fix anything on my Kenmore washer during the time I owned it - it was GREAT!! I miss it dearly now.....

Though they were both newer GE models I really don't care for GE anything, as I think they are poorly built, as well as is their refrigerator brands as well.

Don't buy GE anything if you don't have to!! You heard it here from me and I know. My GE washer already broke a belt not even being 8-9 years old, and it was hell to replace, and never worked right afterwords as for the water pump part. Very POOR design! Oh well...

The gas dryer works fine, but the lint collector is not anywhere as good as my old Kenmore was. Poor design in my opinion.

I'm looking for another Kenmore or Whirlpool (set) model now, as they are the best. Kenmores are made by Whirlpool btw, just in case you didn't know that. The best in the business!

As to your other possible noise scenario -

The only other weird noise scenario you'll experience if it's a Kenmore dryer is when the drum "spring loaded track IDLER wheel" goes bad. This drum IDLER wheel is located under the drum itself at the back part of the drum and rides in a groove in the drum itself. It also helps to stabilize and counter-balance the drive belt-loaded turning drum that rides on this drum IDLER wheel as it turns. If your dryer does have the rear drum IDLER wheel system, then it just depends on the make and model. Kenmores & Whirlpools are designed this way. Very good design I might add!!

Some, or all GE dryer models may have a rear drum centering bearing assy instead - and in addition to - a front (Support, 3 glide front drum bearing part# 2359 & a Drum front slide bearing part# 2305 times 3 needed). If this/these front support/slide bearing part(s) goes bad usually the "felt duct" will need to be replaced as well. It not only helps to seal and quiet the drum that runs on the Support part, but it also helps to keep clothes from getting in-between the Support C part and helps prevent clothes from getting damaged. If those (3) friction sliders wear out or fall out, and take out or damage the "felt duct" as well, then the noise will be horrendously LOUD.

The front part of the GE drum models usually rides on a separate front panel support assy which can be made of a plastic C shaped device with anti-friction pad strips to help in frictionless rotation of the drum. A cheap but pretty effective design that does away with a front IDLER wheel, or pair of IDLER wheels as it were at the front of the dryer's frame which houses the door assy as well.

Though my Kenmore replacement drum IDLER wheel only cost me around $17 many years ago I see they now are anywhere in the $30+ range. Ouch! If it's the GE rear bearing assy that has gone bad - another Ouch as that part runs around $50+. Just depends on where you are and parts availability.

Most Kenmore/Whirlpool model dryers with the rear spring loaded drum IDLER wheel design do not have a ball bearing design, but rather have a typical cheaper brass bushing design instead, and when the grease lubricant dries out or they become dirty from picking up dirt in the air such as lint from the drum, etc then they begin to SQUEAL or WHINE very loudly.

The longer this goes on like this the hotter the drum IDLER track wheel gets until it melts the "typically" molded plastic housing, and then it really makes a lot of noise, and could actually lend to the drum belt breaking - as due from the added friction & stress from the binding wheel. It can also damage the front "felt duct" material as well. I had to repair mine as best I could as they had n factory replacement part that I knew off.

The only other mechanical parts that could possibly make any squealing type noise would be the electric belt drive motor or the heat blower motor being gas or electric. If the heat blower motor uses a cheaper brass sleeve shaft bushing bearing that would be rare, but could be a noise source as well. The belt drive motor rarely rarely would ever go bad!!

I hope this info helps to narrow down your problem if you are not able to at least open the top up to inspect the dryer yourself. Always unplug the 110VAC power before opening any cover or panel part up though!

That will not only prevent any electrical shock hazard, but will also keep the gas from turning on by mistake - as by solenoid design - if your dryer is gas.

I suspect this is what's wrong with your dryer.

Again - I hope the info helps you out...

Best regards,

Frank

Posted on Mar 05, 2008

Ad
  • 11 Answers

SOURCE: GE profile model # DPSQ475ETWW or ET0WW drum belt slipping

the rubber side should be on the drum

Posted on Jan 11, 2009

  • 40 Answers

SOURCE: My GE Dryer model DWSR483EA1ww will not stop & doesn't dry quick

first thing you should do is check the flow of your vent, a clogged vent can cause all your problems check it outside while the unit is running you should get really good flow compare it to the flow of the dryer with the vent hose off the dryer completly. they should be fairly close or just run it with out the vent hooked up to the vent if you have an electric but not with a gas dryer

Posted on Mar 09, 2009

garing
  • 998 Answers

SOURCE: Whirlpool Dryer Leaves black marks on clothes

change drum seal

thumbs up

Posted on Aug 17, 2009

  • 1 Answer

SOURCE: GE Profile takes too long to dry a full load of clothes

could be holding coils not opening all the time

Posted on Sep 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My dryer sounds like there are metal balls rolling around inside when clothes are drying


Sounds like the rollers are worn out. If they are fine then see if the dryer has glides on the drum.





Apr 23, 2014 | GE Profile Wizard DPSE592EAWW Electric...

1 Answer

GE digital timer 15313 has 3 wires, black, blue and green. Wall switch wires have bare, black, red and white from one line, and black and white from the other line. I've tried every combination


It sounds like you are replacing 3-way switch.
Low voltage light? Are these lights connected to 120Volt circuit?

I think you want the GE 15312 timer, instead of GE 15313.
http://waterheatertimer.org/How-to-wire-GE-15312-timer.html

GE 15313 is for single-pole incandescent light bulbs only.

This is live answer 11-2012
Add a comment for more interaction on answer.

Nov 22, 2012 | Hardware & Accessories

1 Answer

Brother MFC-440CN - print quality terrible, almost non-existent in spite of many cleaning operations.


It sounds like the printhead needs to be replaced. Brother may cover the cost of repair if you call them at 877-276-8437 and tell them the prints are "missing black ink". Very common problem that a new printhead should fix.

Oct 08, 2012 | Brother MFC-440CN InkJet Printer

1 Answer

My washing machine is leaving small bits of black


FIXYA has no way of knowing what they are or where they come from .we have no field techs . suggest you call a repair service

Oct 26, 2017 | GE Profile WPRE6100G Top Load Washer

2 Answers

My washer leaves black marks on my clothes. I do not use fabric softners


Do you mean Black, really black marks? Perhaps dark brown.

Some marks comes from moldy seals, other marks comes from leaking gears from the machine. Examine the marks, check if those marks are oily or not.

Nov 27, 2009 | Fisher Paykel EcoSmart GWL15

1 Answer

GE Easycare Wiring Specs


Not sure what part of the machine component you are referring to but generally the colours mean the following using 240 volts:

Red=Active
Black=Neutral
Green or Green/Yellow=Earth (ground)
White=Switched Active (Become active via a switching component).

I think you should clarify what your attempting to wire up before proceeding.

Aug 20, 2008 | GE Profile Harmony DPGT750EC Electric...

1 Answer

GE Profile Performance Dryer


GE Easy care 4 prong Installation

Grn = Ground
White = Neutral ?
Black = ____ top or bottom?
Red = ____ top or bottom?

Please advise

Aug 19, 2008 | GE Profile Harmony DPGT750EC Electric...

1 Answer

GE Profile power cord


White is the neutral circuit and it goes to the center connection of the terminal block on the dryer. Red and Black are "hot" wires and they go to the connectors on the ends of the block, doesn't matter which color is on which side. Green is the ground and it goes to the cabinet ground.
Post back if you have any questions.
Mike

Jan 06, 2008 | GE Profile Harmony DPGT750EC Electric...

1 Answer

Black Marks on Clothes Coming out of the Dryer


Follow-up the Nov 28 post: Just got my replacement dryer after many phone calls to LG. The installer told me that the black marks were from using dryer sheets. He said the ozone system in the dryer breaks down the chemicals in the dryer sheets. Doesn't explain why the problem seems to be fixed when roller and drum is replaced then returns after about 2-3 months.

Oct 09, 2007 | LG DLE2514 Electric Dryer

Not finding what you are looking for?
GE Profile DPSB613G Gas Dryer Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Dryers Experts

John Tripp
John Tripp

Level 3 Expert

4654 Answers

JP Services
JP Services

Level 2 Expert

310 Answers

Cindy Wells

Level 3 Expert

5166 Answers

Are you a GE Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...