Question about Mtd Products Yard Machines 158CC Tiller

Open Question

A friend gave me a mtd yard machine tiller.it runs good but the cable lines are frozen and need to be replaced plus it needs a tire,and new belts.the problem is the product information is so worn it can't be read.i need the model number and year to order the parts,how can i find this info.

Posted by on

  • Anonymous Apr 03, 2009

    I have a MTD rear tine tiller. the only numbers I can find are on the engine M.N. 135202 S.N. 02501 This is about a 1998-99 vintage machine. I called MTD and was told these are engine numbers. I need the bakelite part in the clutch cable release on the left handle bar. how do i find this $5 part?

×

1 Suggested Answer

KMusselmann
  • 247 Answers

SOURCE: NEED THE BELT SIZE FOR TILLER ,MODEL NUMBER

Well I cannot find the size but I did find the part # and a place to order the part. Hope this helps
Kurt
Part # 754-0434
Can get from the following
http://www.buymtdonline.com/webapp/wcs/stores/servlet/Home_YardMachines_10101_19502_-1

Posted on Apr 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I can't start my cub cadet snowblower. Pull rope is stuck. How can I fix?


Take the cover off the rope starter and look for broken parts, also are you sure the engine is not frozen up?

Jan 12, 2017 | Cub Cadet Garden

1 Answer

My john deere44 inch snowblower is throwing belt consistently, just started doing it


check the alignment of the pulleys
use a straight edge across the pulley flanges to ensure they are in line

Jan 08, 2017 | Garden

1 Answer

I have a Ariens snowblower deluxe 30 which is a year old. Starts fine and will run. Unfortunatley it is running way to low. I have replace the gas with fresh gas ran it through completely


It is very possible the carbureator needs a cleaning. Moisture can corrode the inner parts of them if left all summer. I find that the fuel usually does not go bad over the summer. I always start my snowblower once a month over the summer and then have no problems when the snow flies again. There was a time when mine was losing power and quitting also. There is a screw on the bottom of my carbureator that needed adjusting. If you are lucky that may be all you need. By turning mine in and out a bit I found the spot where the gas was correct and it worked fine again.

Jan 08, 2017 | Ariens Garden

2 Answers

How to replace pto wire on Kubota L2800


No need to remove any panels. the bottom end attaches to a lever on the right hand side of the transmission. Can be reached from under the tractor. There was an update on the control cable which changes the angle of the bracket on the top end so the wire does not bend and break so quickly. check with you dealer to see if yours qualifies.

Jan 01, 2017 | Kubota Garden

1 Answer

I can start my barracuda but it won't run at more than idle


Timing problems, bad or warn cam shaft lobes, fuel pump going bad, no pressure. Worn corroded rubber gas tank lines, from the tank to the hard lines, just forward of the gas tank, under the car. Inspect for gas leaks.

May 28, 2015 | Garden

1 Answer

My weed eater will not run with the choke setting wide open.


You may have a pinhole or crack in the small hose that runs from the fuel tank to the carburetor. If equipped with a primer it may also have a small crack or pinhole. Either case may cause the carb to suck air instead of gasoline. Other possible reasons are a plugged muffler causing too much back pressure or a partially clogged fuel filter. (The fuel filter on many weed whackers are located inside the fuel tank at the end of the fuel line.)

Aug 28, 2014 | Garden

2 Answers

Do you have free manuals of Kubota mowers?


Try requesting manuals directly from Kubota.

Jul 16, 2014 | Kubota Garden

2 Answers

My starter string broke on my troybilt lawn trimmer, how do i fix it


Disassembly of the covers and controls to that point will be needed. It takes a little bit of work, then you have to preload the spring tension on the recoil unit BEFORE you install new rope. A good little bit of labor involved....somewhat mechanically inlined?

Aug 27, 2010 | Troy Garden

Not finding what you are looking for?
Mtd Products  Yard Machines  158CC Tiller Logo

Related Topics:

239 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mtd Garden Experts

Dwain Pippen

Level 3 Expert

376 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

375 Answers

Jim Parker
Jim Parker

Level 3 Expert

1040 Answers

Are you a Mtd Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...