Question about GMC W3500 Pressure unit. oil. sensor,engine oil press. sensor. oil

1 Answer

Where is oil presure sendind unit on 2000 blazer V-6

Posted by on

  • Chris Sampson
    Chris Sampson Apr 25, 2013

    remove the distributor and replace sending unit located behind it---has a plug in and you need an 24 metric wrench to replace it-----this pressure unit if bad will cause your fuel pump to shut down to save the motor if run low on oil as my wife did----if car starts when fuel in poured into carb then this is your problem

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 18,391 Answers

Oil sending unit is under intake manifold, just behind the oil filter on the passenger side (difficult to see-use flashlight). Best option to change : Get everything to do an oil change, removal of the filter makes easier access..

Posted on Apr 22, 2013

Testimonial: "This sending unit was found on the top of motor behind the distributor -----must remove the cap and rotor and distributor to replace it---it takes a 24 metric metric wrench to remove-----this unit also controls the fuel pump on the car so before you change a fuel pump at $300 try this first "

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My roller brush on my d33 stops when presure or after i put the guard back on


If the belts in the clutch have lost elasticity the belt can slip on the motor shaft rather than turning the brush roll.

Jan 06, 2017 | Vacuums

1 Answer

2000 chevy blazer 4wd stumble stall on start and idle


Its not The mechanics fault all the time, you may fix something then something else goes wrong thats mechanics 101. I've had this problem before I replaced my ignition coil and my fuel pump, fixed it right up in my 96 f150. Give it a try its a whole lot cheaper than most options.

Jul 18, 2013 | Dorman 2000 Chevrolet Blazer Switch /...

1 Answer

Gas to oil ratio for dayton chainsaw model 2z971


Hi montorsewill...
You will use a 50:1 Oil to gas ration...1 pint of 2 cycle oil to 6 gallons of gasoline
Please take time to rate me

Sep 02, 2011 | Vacuums

2 Answers

How much oil would i ad to a pint of gas at a 50 to1 ratio


A pint is 16 ounces, add 1/3 ounce of oil for a 48:1 mixture.

Gary

Aug 30, 2011 | Vacuums

2 Answers

I have the brother Ls-2000 sewing machine i threaded the top as well as the bobbin but when i try to sew the thread gets stuck and it bunches up and tangles in the bobbin. also the little bit that did sew...


adjust your tension.You probably did not wind your bobbin properly as well.Make sure you oil your machine every month or so and make sure your bobbin is seated properly before you sew.
Go slower with the pressure foot speed and use the right needle.ALWAYS test on scrap of your sewing material first!!!

I have this machine for like 2 years and can do 2-5oz cowhide and buffalo leather on it (no joke, and it works FLAWLESSLY) inside it has full steel construction,just needs regular oiling compared to pro machines and easily made a few grand $$$ with it while my pro machine is getting repaired (I don't even bother with my pro machine anymore) But you MUST oil it every month and use the RIGHT needle and adjust your tension properly
Also pull out the thread a good 6 inches from the needle and bobbin before dropping the pressure foot and sewing.
Best $70 bucks (WITH TAX) I spent hell,the leather I use costs more than the machine!

Jan 12, 2011 | Vacuums

1 Answer

Do you have manuals for a Bissell carpet machine model 1640-6? This machine is about 25 years old. I forgot how to set up soap dispenser


BISSELL User's Guides can be downloaded at www.bissell.com
On the front page under Customer Service click on User's Guides and enter the model number of your unit.
User Guide will be displayed as a PDF file.
Model 1631 is a faucet hook up unit similar to the 1640-6. 1631 User's Guide is on the BISSELL website and should be a similar set up to the 1640-6.

May 01, 2010 | Bissell Carpet Cleaner Powerbrush Deep...

1 Answer

What is the proper equipment to use in vacuum filter cleanng?


I have blown out filters with presure hoses and I have washed filters, both ways will clean them. they say once a filter has been cleaned it will start to lose its effectiveness. Clean till you can buy new ones.

Oct 24, 2009 | Vacuums

1 Answer

THE VACUUM CLEANER WORKS FOR 6-7 MINS THEN CUTS OUT, THEN AFTER A WHILE STARTS AGAIN FOR A FURTHER 6-7 MINS THEN KEEPS REPEATING THIS PROBLEM


What you describe is typical of a machine that's overheating. This is almost always caused by a blockage. Check the machine thoroughly for any blockages, including any filters, and my bet is that you will find something that shouldn't be there that needs removing (or possibly replacing). I hope this helps.  Good luck!

Mar 02, 2009 | Electrolux UltraLux 2000 Bagged Canister...

1 Answer

Vacuum Repair


Take the screws out of the bottom plate. Take the 2 screws out of the drive motor- opposite end of where the belt goes. Loosen the 2 screws where the belt goes, put the belt on and replace the screws. Make sure to thoroughly clean the brush while you have it apart. Don't oil the bearings. Oil will only make the dirt stick and jam the bearings.

Aug 15, 2008 | Electrolux UltraLux 2000 Bagged Canister...

Not finding what you are looking for?
GMC W3500 Pressure unit. oil. sensor,engine oil press. sensor. oil Logo

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18391 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

JoeVacs

Level 2 Expert

357 Answers

Are you a GMC Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...