Question about Simrad AP35 GPS Receiver

Open Question

I have problem with my autopilot AP35 in display see valid data not available gps 1

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ginko
  • 19396 Answers

SOURCE: AP35 Autopilot

Yep, if rudder calibration values are OK, then there is a real problem with calibration, it can be a mechanical problem or a faulty rudder feedback unit. Follow procedure at page 93 of user manual :
AP35 Autopilot Instruction Manualto troubleshoot the error, if you cannot get rid of the error message you may have to replace the rudder feedback unit or to have the unit inspected by a technician.

Posted on Aug 14, 2008

  • 111 Answers

SOURCE: where can I get an installation manual for a rpu80

I have one right here. It covers the RPU80, 160 & 300. It's $15.00 plus shipping. Call me at 410-228-7335 if you're in the U.S.

Posted on Feb 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

G-Pilot 3100 Autopilot


Go to www.atomic4.com and they have display repair kits for the Navman Instruments.

Apr 03, 2010 | Navman F3100 DISPLAY ONLY AA002611R GPS...

4 Answers

I AP 35 Setup


ensure you are setting correct rudder value.

Aug 14, 2008 | Simrad AP35 GPS Receiver

1 Answer

Where can I get an installation manual for a rpu80. I am installing an AP35 autopilot on my boat but the instructions do not cover the installation of the remote pump.


I have one right here. It covers the RPU80, 160 & 300. It's $15.00 plus shipping. Call me at 410-228-7335 if you're in the U.S.

Feb 01, 2010 | Simrad AP35 GPS Receiver

1 Answer

I would like to connect my garmin gps72 via the garmin supplied four line plug to the nmea ports in back of my raymarine st6002 autopilot controller. The st6002 controller is plugged into a smartpilot x5...


I connected my Garmin gpsmap76 to a Raymarine autopilot using the NEMA output from the GPS. The autopilot was also on the seatalk bus. It work fine. The GPS provided navigational guidance to the autopilot

Dec 21, 2009 | Garmin GPS 72 GPS Receiver

1 Answer

Connect Furuno 1732 to st8002 autopilot


It will handle the voltage. as far as the wiring goes, you'll have to decide which port to use. the wire coloring is different. you'll have to send your nmea out data from port 3 white and shield ( Like you said) to the pilot and receive your heading data from the pilot on port 2.

Apr 11, 2009 | Furuno Navnet 1732 GPS Receiver

1 Answer

Problems talking to autopilot


I think you use the NMEA output to the autopilot .
The plotter shows you only when you have a seatalkconection with a Raymarine autopilot on you Plotter

Apr 06, 2009 | Raymarine E120 Multifunction GPS Receiver

1 Answer

Simrad Autopilot won't turn on


Try and turn on the unit at the J300-40 pcb by using a test light one end to gnd and going to the ap35 interconnect and touch the test light to each pin or until you hear the unit start up.

Dec 19, 2008 | Simrad AP35 GPS Receiver

1 Answer

AP35 Autopilot


Yep, if rudder calibration values are OK, then there is a real problem with calibration, it can be a mechanical problem or a faulty rudder feedback unit. Follow procedure at page 93 of user manual :
AP35 Autopilot Instruction Manualto troubleshoot the error, if you cannot get rid of the error message you may have to replace the rudder feedback unit or to have the unit inspected by a technician.

Aug 14, 2008 | Simrad AP35 GPS Receiver

1 Answer

GPS Error Message on Start Up Model GM-7-1


sounds like your firmware or sd card is corrupt, unfortunately this is common on these. I created a dvd with the map and program data to reload everything in your unit, it also updates the map data to the last version issued. you can find it in ebay by searching for finedrive 400 map...

Jun 01, 2008 | Fine Digital FineDrive 400 GPS Receiver

1 Answer

The S1G display occasionally shows no data. The autopilot works fine for hours then fluxgate seems to hang up.


Try to borrow a computer unit to detect if the fault is in the computer unit or the display unit

Mar 19, 2007 | Raymarine ST6001 S1G Hydraulic GPS...

Not finding what you are looking for?
Simrad AP35 GPS Receiver Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Simrad GPS Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

The Knight
The Knight

Level 3 Expert

74106 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Simrad GPS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...