Question about Elmo Projectors EV-200 Slide Projector

1 Answer

Elmo EV 200 can no longer focus. Any suggestions for repair options?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Remove the orange plastic parts near the camera.

There is a square opening/hole.

Get a long small screwdriver and adjust the screw connected to the lens.

I did this with it on, so I could see if it was making a difference. I am not 100% sure if adjusting the screw was the fix. However, moving stuff around in that area seemed to make a huge difference.

Posted on Oct 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the diagram of a elmo for repairs


I found a manual for this classroom projector at projectorcentral.com in their .pdf library. Good Luck !!!! Jim

Sep 27, 2012 | Elmo Projectors Tt-02s Slide Projector

1 Answer

The autofocus will not focus. The paper is blurry. How can I fix it?


Remove the orange plastic parts near the camera.

There is a square opening/hole.

Get a long small screwdriver and adjust the screw connected to the lens.

I did this with it on, so I could see if it was making a difference. I am not 100% sure if adjusting the screw was the fix. However, moving stuff around in that area seemed to make a huge difference.

Sep 08, 2010 | Elmo Projectors EV-200 Slide Projector

1 Answer

Need to upgrade video camera in an Elmo TRV-s8


Not sure if that can be done but give Elmo Service a call. www.elmousa.com

Feb 23, 2010 | Elmo Projectors TRV-35H Slide Projector

1 Answer

Shows a blue screen


Make sure power is plugged in and power switch set to on.

Make sure TV or projector is plugged into video out.

Make sure the input switch is set to Main and not video in.

Nov 20, 2009 | Elmo Projectors EV-200 Slide Projector

1 Answer

Is there a power indicator?


No, there is no power indicator light.

Oct 13, 2009 | Elmo Projectors EV-200 Slide Projector

1 Answer

Elmo TRV-35H "eating" slides


CAUTION: Mains voltage connections are exposed once the base of the projector is removed. ONLY attempt repairs if you are confident of your skills!

There are several possible causes for this problem:

1. Kodak produce two different types of carousel magazines - one for glass mounts and one for card mounts. You must not mix glass and slide mounts in the magazine - it causes the focus mechanism to 'hunt' and also causes the slides to jam, as described.
2. These projectors are almost antiques ..... lubricants dry out and the mechanisms slow down and stick! Some 'technicians' apply graphited grease over the top of the dried stuff, hoping it will soak in! Clean as much of the old lubricants off with 'electronic component' solvent on cotton buds particulalrly around all of the cams. Pay particular attention to the slide lifter cam follower - grease here can cause the lifter to only lift, or drop, the slide partially though its full travel. I use 'CopperEase' very, very sparingly on the cams (NOT on the face of the slide lifter cam) and haven't experienced any problems.
You should not adjust the cams on their shaft.
3. The slide pressure plate is acuated through one of the cam followers, opening and closing at the right time. There is a very fine pivot bar at the bottom of the plate. The pivot points can be lubricated with a single small drop of fine industrial sewing machine oil. Avoid 3in1 oil at all cost!

Jun 20, 2009 | Elmo Projectors TRV-35H Slide Projector

1 Answer

ELMO document camera only shows documents in black and white, not color. Is there something wrong with the bulb? the camera?


My ELMO unexpectedly stops working during class. The blue power light is still lit but the ELMO is not recognized through my projector.

Any suggestions on what the problem may be?

Mar 25, 2009 | Elmo Projectors EV-200 Slide Projector

1 Answer

My ELMO video presenter is not working. When I connect it to the video projector via s-video cable, it no longer shows an image, but the projector recognizes there is a signal. It recently fell off of a...


you'll have to check the elmo usa website. you can either send it to elmo themselves, or to one of their authorized service centers (website). if the camera itself is damaged, it's pretty expensive. it may just be the s-video socket.

Dec 11, 2008 | Elmo Projectors HV-8000SX Slide Projector

1 Answer

How do we know the Elmo is on?


use another power cabel-dissconect from outlet and check for broken fuse-if everything is ok.change exposure lamp.

Oct 09, 2007 | Elmo Projectors EV-200 Slide Projector

Not finding what you are looking for?
Elmo Projectors EV-200 Slide Projector Logo

Related Topics:

252 people viewed this question

Ask a Question

Usually answered in minutes!

Top Elmo Projectors Slide Projectors Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

The Knight
The Knight

Level 3 Expert

68427 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

13160 Answers

Are you an Elmo Projectors Slide Projector Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...