Question about Ezonics EZVideo Chat Kit Webcam

1 Answer

S120H Low volume

When I shout, I am barely able to get a response from the mic supplied with my S120H webcam. Is there software to bring up the input?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Expert
  • 8,637 Answers

Go to Control Panel and Click on Sounds, Click on Audio, then Click on the Microphone. Then Click on the drop down and select Camera Microphone or Headset.
Click OK and it should work.
Web Camera’s have to be setup on the program they are to be used with. Just installing the camera on your Computer does not set it up to broadcast on messengers or Skype. Each program has Options that have to be setup in order for the Audio and Video to function properly.

A. Skype Setup:
After downloading and installing Skype (http://www.skype.com/intl/en-gb/download/skype/windows/beta/downloading/) set it up as follows:
1. Go to Tools, then Options, and click on Audio Settings and set the Microphone and Speakers to the computer Audio Card.
2. Then click on the Video Settings.
3. The camera if Installed Properly will come up and show a video picture.
4. Then, on the bottom of the page click on Save.
The camera and audio should function properly. Your friends and Family will now be able tosee and her to you.

B. Yahoo Setup:
After downloading and installing Yahoo Messenger (http://www.soft32.com/download_30.html) set it up as follows:
1. Go to Messenger at the top left and click on it.
2. Next go down to Preferences and click on it.
3. Next Calling and Devices on the right and set the Microphone and Speakers to the computer Audio Card.
4. Next go to the Test Audio section and (in blue writing) click on “Open the call setup assistant” and follow the instructions on the left window.
C. Windows Live Messenger:
1. After you start Windows Live Messenger, expand the view by clicking on the square on top left next to the red X.
2. Then on the Windows Live messenger window on the right side, click on “ “Show Menus.” And then click on “Show the Menu Bar”.
3. Next go to the Menu Bar on right side, click on “ “Action.”
4. Go to “TOOLS” and click “Audio and Video Setting” and follow the instructions.
NOTE: Your audio and video should work. Enjoy.

When done both the Audio and Video will function properly so you can chat and see family or friends you are connected to.
D. AIM (AOL) Messenger
Go to this site http://dashboard.aim.com/aim and Launch AIM AOL Messenger.
1. On the VIM sign-in window click on Edit.
2. Then click on Settings Enhanced IM.
3. Next click on Enhanced IM.
4. Then click on Audio Video.
5. The Audio and Video portion has drop downs so you can select the proper audio card and video camera installed in you computer.
The Audi Video drop downs are
Microphone
Speaker
Camera
The audio and camera should function now.

Additional information to use with VIM settings,

Adjust Your Audio and Video Settings:
In order to adjust your audio and video settings, please follow the steps given below:
1. Click the Audio and Video Settings button directly below the My Buddy or My Camera window. If you are currently participating in an AOL Live Video IM session, a message will display: You must disconnect the current AOL Live Video IM conversation before running setup. Would you like to disconnect now? Click the Yes button.
2. The Audio and Video Tuning Wizard will appear to help you verify that your camera, speakers and microphone are working properly. Follow the on-screen prompts.
Notes:
· The first time you use AOL Live Video IM, a message will display: Would you like to first check your audio and video settings? Click the Yes button. The Audio and Video Tuning Wizard will appear to help you verify that your camera, speakers and microphone are working properly. Follow the on-screen prompts.
· images in AOL Live Video IM may appear reversed, or as a mirror image (text may appear backwards) when you look at your own camera feed or at the picture-in-picture (PIP) display.
After making the settings your ready for a chat and video talk with your Family and Friends. Hope this helps. Bud

Posted on Aug 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there any way to adjust the mike on logitech webb cam


First of all make your webcam the default mic on your computer
Plug in webcam

TEST SPEAKERS
Right click on speaker icon in System Tray or from Control Panel
Select "Playback Devices"
The speaker icon ( checked as working) and volume level graph should be visible
Right click on the volume graph and click "Test"
Left hand speakers followed by right hand should be heard

SET DEFAULT & TEST MIC
Click "Recording" tab.
To set required (webcam) mic as default - click on mic font to highlight and click "Properties"
In lower dropbox display "Use this device enable" click 'OK'
Click "Levels" tab and ramp up sliders ( adjust to suit later)
Return to "Recording". Test mic by speaking and make sure volume graph displays

RESTART COMPUTER ( IMPORTANT )
You can now adjust the mic by clicking on the speaker icon down in the notification area ( by the clock )
If its not there - right click on the lower task bar ( a blank area) and select 'Properties' click 'Notification area) and check the box for 'volume' > Apply > OK

During the webcam software upload you may not have opted for the Logitech shortcut on your desktop - if so > Start > All Programs - locate the logitech folder and expand it - right click on the logitech software ( with the webcam icon) and select ' Send to - Desktop create shortcut'

Plug in your webcam
Launch the webcam dashboard (toolbar) by double-clicking the shortcut icon and open the 'Settings' menu ( 2 gearwheels)
Select the mic icon to make any changes

Jul 26, 2010 | Logitech Webcams

1 Answer

My sound on the webcam is not working


Make sure the webcam mic is set as default
TEST SPEAKERS
Right click on speaker icon in System Tray or from Control Panel
Select "Playback Devices"
The speaker icon ( checked as working) and volume level graph should be visible
Right click on the volume graph and click "Test"
Left hand speakers followed by right hand should be heard

SET DEFAULT & TEST MIC
Click "Recording" tab.
To set required (webcam) mic as default - click on mic font to highlight and click "Properties"
In lower dropbox display "Use this device enable" click 'OK'
Click "Levels" tab and ramp up sliders ( adjust to suit later)
Return to "Recording". Test mic by speaking and make sure volume graph displays

Restart computer and configure to your chat program

Jul 16, 2010 | Logitech Webcam

1 Answer

I can't make my webby work with msn. it works off


Plug the webcam in and set your webcam mic as default

TEST SPEAKERS
Right click on speaker icon in System Tray or from Control Panel
Select "Playback Devices"
The speaker icon ( checked as working) and volume level graph should be visible
Right click on the volume graph and click "Test"
Left hand speakers followed by right hand should be heard

SET DEFAULT & TEST MIC
Click "Recording" tab.
To set required (webcam) mic as default - click on mic font to highlight and click "Properties"
In lower dropbox display "Use this device enable" click 'OK'
Click "Levels" tab and ramp up sliders ( adjust to suit later)
Return to "Recording". Test mic by speaking and make sure volume graph displays

Restart computer

Test your webcam here to make sure it broadcasts ok - Hit 'Allow' in the top window and check your cam in the left hand panel.

http://www.testmycam.com/

If it fails to work here concentrate on your webcam drivers and software before moving forward.

Set your webcam mic (if it has one as default)
Vista -

Having proved your cam is working ,you can configure it to WLM (MSN)

CONFIGURE SOFTWARE to MSN
Its good practice to disconnect and re-connect your webcam before you start - if you have been using it elsewhere the MSN software may have difficulty in locating it, even if you exited the previous program correctly.
The reason being, the webcam software can remain hooked-up to a program and needs to be rebooted.
Mine, I just unplug it from the USB and plug it back in to reboot the software.
If yours is integral with the computer you will have to re-start the computer, use a keyboard shortcut or disable / enable the webcam from the Device Manager.

Open MSN
Click 'Open Menu'
From 'Tools; navigate to, and click, 'Audio and Video setup'
Set your speakers
Click 'Test' - if OK, move on.
Set your mic as default
Use the slider to set volume and test.
Click 'Next'
This takes you to the video setup
Your webcam should be broadcasting - (if not - make sure the webcam is set as default - restart MSN)
Use 'Webcam Settings'to fine tune the picture.
Click 'Finish'



Jul 15, 2010 | Microsoft LifeCam VX-1000 Webcam

1 Answer

I didnt install the mic that came with this webcam when i got it and i can not find the disc. is there any way for me to install the mic through the internet?


The software for the mic comes as part of the Logitech bundle - you may have a laptop or another mic also installed
Try setting your webcam mic as default
Vista
TEST SPEAKERS
Right click on speaker icon in System Tray or from Control Panel
Select "Playback Devices"
The speaker icon ( checked as working) and volume level graph should be visible
Right click on the volume graph and click "Test"
Left hand speakers followed by right hand should be heard

SET DEFAULT & TEST MIC
Click "Recording" tab.
To set required (webcam) mic as default - click on mic font to highlight and click "Properties"
In lower dropbox display "Use this device enable" click 'OK'
Click "Levels" tab and ramp up sliders ( adjust to suit later)
Return to "Recording". Test mic by speaking and make sure volume graph displays

Restart computer and configure to the chat program

Jun 17, 2010 | Logitech 961462-0403 Webcam

1 Answer

I'm trying to figure out how to get my webcam where I can talk on Windows Live Messenger, and I can't figure it out.


First job is to set your webcam mic as default
TEST SPEAKERS
Right click on speaker icon in System Tray or from Control Panel
Select "Playback Devices"
The speaker icon ( checked as working) and volume level graph should be visible
Right click on the volume graph and click "Test"
Left hand speakers followed by right hand should be heard

SET DEFAULT & TEST MIC
Click "Recording" tab.
To set required (webcam) mic as default - click on mic font to highlight and click "Properties"
In lower dropbox display "Use this device enable" click 'OK'
Click "Levels" tab and ramp up sliders ( adjust to suit later)
Return to "Recording". Test mic by speaking and make sure volume graph displays

Restart computer

CONFIGURE TO MESSENGER
Test your webcam here to make sure it broadcasts ok - Hit 'Allow' in the top window and check your cam in the left hand panel.

http://www.testmycam.com/

If it fails to work here concentrate on your webcam drivers and software before moving forward.

Set your webcam mic (if it has one as default)
Vista -

Having proved your cam is working ,you can configure it to WLM (MSN)

CONFIGURE SOFTWARE to MSN
Its good practice to disconnect and re-connect your webcam before you start - if you have been using it elsewhere the MSN software may have difficulty in locating it, even if you exited the previous program correctly.
The reason being, the webcam software can remain hooked-up to a program and needs to be rebooted.
Mine, I just unplug it from the USB and plug it back in to reboot the software.
If yours is integral with the computer you will have to re-start the computer, use a keyboard shortcut or disable / enable the webcam from the Device Manager.

Open MSN
Click 'Open Menu'
From 'Tools; navigate to, and click, 'Audio and Video setup'
Set your speakers
Click 'Test' - if OK, move on.
Set your mic as default
Use the slider to set volume and test.
Click 'Next'
This takes you to the video setup
Your webcam should be broadcasting - (if not - make sure the webcam is set as default - restart MSN)
Use 'Webcam Settings'to fine tune the picture.
Click 'Finish'

Jun 15, 2010 | GE EasyCam Webcam

1 Answer

Adio capture is very low


check your basic audio settings
Vista
If you have an earlier OS, you may have to access your hardware from the Control Panel.

TEST SPEAKERS
Right click on speaker icon in System Tray
Select "Playback Devices"
The speaker icon ( checked as working) and volume level graph should be visible
Right click on the volume graph and click "Test"
Left hand speakers followed by right hand should be heard

SET DEFAULT & TEST MIC
Click "Recording" tab.
To set required mic as default - click on mic font to highlight and click "Properties"
In lower dropbox display "Use this device enable" click OK
Click "Levels" tab and ramp up sliders ( adjust to suit later)
Return to "Recording". Test mic by speaking and make sure volume graph displays
Restart computer

Dec 14, 2009 | Microsoft LifeCam VX-3000 Web Camera

1 Answer

Need more mic volume


Plug webcam into USB
Right click on speaker icon in the system tray by the clock.
Select 'Recording devices'
Click on your mic to highlight in blue
Click properties
Click 'Levels' and adjust slider
Click OK
Click 'Playback' tab
Click on Speaker to highlight
Click 'Properties'
Click 'Levels'
Increase speaker level if low
Click OK

Aug 22, 2009 | Microsoft LifeCam VX-1000 Webcam

1 Answer

Cant hear enything when i am speakin with friend on the mic


Unplug the camera, remove all the Logitech camera AND Logitech camera drivers via Control Panel/ Remove Applications, then reboot. After re-boot, plug in the camera, Windows will identify it as a USB Camera / Mic and it will work in all applications including Skype. You will not have access to the Logitech menus but the camera and Mic WILL WORK in all your communications needs. After a number of instances where I lost my Mic input, I finally gave up on the Logitech software since they are incapable of finding the Windows Update driver that conflicts with their own driver. Although mine is currently working fine as a Windows recognized "USB Camera Mic", the next Webcam I get will NOT be Logitech. It's a great Webcam but since they are clearly incapable of keeping their software compatible with Windows updates, I'll switch to another make. Hope this helps.
JamesTBaines@BTopenworld.com

Mar 08, 2009 | Logitech Quickcam Chat Webcam

3 Answers

I need ezonics webcam software


I need ezonics s120h drivers! Please help!

Aug 11, 2008 | Ezonics EZCam Webcam

2 Answers

Help please


check the settings on your msn that the input is set to the mic and also on the sound in control panel that input is set to labte mic

Sep 30, 2007 | Labtec Webcam Pro

Not finding what you are looking for?
Webcams Logo

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ezonics Webcams Experts

micky dee

Level 3 Expert

2624 Answers

Teet Bergmann

Level 3 Expert

565 Answers

Shahzad  Waseem...
Shahzad Waseem...

Level 3 Expert

746 Answers

Are you an Ezonics Webcam Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...