Question about Whirlpool 30" Self-Cleaning Freestanding Gas Range - White-on-White

Open Question

Have a Whirlpool Accubake gas stove Model SF362LXSQ . how do Ichange the oven light bulb?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

aborcass
  • 2651 Answers

SOURCE: Whirlpool Gold Accubake oven

depress the broil button for 5 seconds it will revert back to Farenheit

Posted on Feb 24, 2008

Krazytech
  • 725 Answers

SOURCE: whirlpool accubake oven error code

F5-E0 Door Error Check Door
F5-E1 Door Latch Check Latch
F5-E2 Door Switch Check Switch

It may just be a door switch

Posted on Jun 12, 2008

  • 2 Answers

SOURCE: whirlpool accubake oven problem

I had the same problem and followed the process listed above....yes, I did unplug/turn off the circuit and am alive to share this update! Right off I noticed that the ribbon cable was loose. For those who have tinkered around with other electronics such as a PC, etc., note that this ribbon cable is not secured by the connector (atleast in my case). Reseated the cable and turned the power on. Voila- the bake option works. Tested it by turning it on for 20-30 seconds. Touched the bake element and got proof that it was working fine (via a singe of the ring finger ;-)).

About three minutes or so later, the display started to beep with an error code - E0 F2. A shorted keypad is what it stands for. The clock was still operable. I could still select the bake option, broil option, etc. Ran a test bake cycle but it turned off after a minute or so and started to display the E0 F2 code again.

Started the process all over ie turn power off, take panel off, reseat ribbon cable. Turn power on and test by holding the Cancel button for five seconds. Still displays the E0 F2 error. Waited for 10 minutes but this time no more beeping or error display. Ran a preheat cycle for 4+ minutes without any problems. The oven warms up and the bake element glows red. Hopefully, all is well. Will see what it does when we bake something the next time.

Thanks to PropHeadTwo and others for their contributions.

Posted on Dec 18, 2008

  • 1 Answer

SOURCE: oven wont work after self clean

I have a Whirlpool MOD. RBS275PDB17 single electric self-cleaning oven; although the manual is generic, it specifies, "When the cycle is completed and the oven cools, "End" will appear on the lower oven display and "LOCKED' will disappear" and "To Stop Self-Clean any time: Press UPPER/OFF, LOWER/OFF or OFF/CANCEL. If the oven temperature is too high, the door will remain locked. It will not unlock until the oven cools." Has your oven had time to cool?

Posted on Dec 21, 2008

  • 1 Answer

SOURCE: gas stove the oven pilot lights but not burner

I HAVE THE SAME PROBLEM WITH MY GE GAS RANGE. THE PILOT LIGHT IS ON BUT WILL NOT IGNITE THE BURNER. WHAT IS THE PROBLEM. LINDA jolin49@yahoo.com

Posted on Jul 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When baking in whirlpool accubake electric stove model GR475LXMS only the broiler works not bottom element what could be wrong?


The element could be open or the thermostat for the oven could be stopping power from reaching the element

Oct 17, 2016 | Whirlpool Ovens

1 Answer

I hav whirlpool accubake.oven wont stay lit.it ignites then flame goes right back out


Whirlpool oven won't light - Appliance Repair Forum

forum.appliancepartspros.com/oven.../225907-whirlpool-oven-wont-lig...

May 19, 2011 - 10 posts - ‎2 authors
I have a Whirlpool Accubake oven (SF362LXSS0) that doesn't seem to be consistently turning on, and the problem's getting worse. ... If I try to turn it on to bake, I hear several clicks, but not that "gas oven turning on" sound and no heat comes out (but a slight smell of gas is ... Whirlpool Gas Oven won't stay lit
1 post
Oct 25, 2012
whirlpool oven won't stay on
1 post
Aug 13, 2012
Whirlpool Gas Oven Will Not Stay Lit
2 posts
Jun 20, 2012
whirlpool accubake oven will not stay lit
1 post
Nov 9, 2009
More results from forum.appliancepartspros.com

Whirlpool Accubake Model # GW395LEGQ4 - Oven won't Start ...


Dec 12, 2015 | Stoves Ovens

1 Answer

Whirlpool accubake oven manual


If you can supply Whirlpool with the model number, they may be able to provide a manual

Aug 19, 2013 | Ovens

1 Answer

Whirlpool gas oven will not heat


most likely you have a bad ignitor,pull out the racks and remove the floor to the stove,turn on the bake,if the ignitor glows but it takes more than 40 seconds for the flame to light you have a bad ignitor even though it glows and if it doesn't glow at all the ignitor is bad,also if the broil lights on top and the bake doesn't change out the ignitor.next time send the model number and i can look up your machine to help you better.

Nov 15, 2011 | Whirlpool Ovens

1 Answer

BROILER WORKS, BUT OVEN BURNER DOES NOT LIGHT Model SF362LXSQ


Hi,

The ignitor is not working right and is going bad....
have the repair man replace the ignitor, or DIY....
Check out this tip about your problem...

Oven not Working or Oven not Heating

Oven Problems Replacing the Igniter


heatman101


ggdh

Feb 16, 2010 | Whirlpool 30" Self-Cleaning Freestanding...

2 Answers

Whirpool gas stove super capacity 465 the stove works but cant get the oven to work


whirlpool super capacity 465 accubake system gas stove with auto starter - oven worked fine the previous night the next day will not do any thing any help out there?

Jan 16, 2010 | Ovens

2 Answers

Whirlpool Accubake Super Capacity 465 gas range. Oven won't light


Some gas ranges may take 10 or so minutes to light.
Other than that you may have a defective glow bar ignitor.
If it glows and does not light the reistance in the ignitior has failed.

Feb 25, 2009 | Ovens

1 Answer

OVEN WON'T LIGHT AND HEAT, NO GAS SMELL


Hi!!! check your oven spark module its inside the oven it looks like this pisture..The module provides the spark to all ignitors..Good luck..




57f9929.jpg

Jan 04, 2009 | GE JGRS14 Gas Single Oven

2 Answers

Whirlpool gold accubake oven won't re-ignite


i have a whirlpool gas accubake range and only two burners will ignite. The other two burners make a clicking sound and release gas but never light. I have to use a match to light the other two burners and the flame is uneven on one. What should i do?

Feb 18, 2008 | Ovens

Not finding what you are looking for?
Whirlpool 30" Self-Cleaning Freestanding Gas Range - White-on-White Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Ovens Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

 Fix Your Board
Fix Your Board

Level 3 Expert

310 Answers

ashburton

Level 3 Expert

417 Answers

Are you a Whirlpool Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...