Question about Heath Zenith SL-6136-WH Basic Solutions Wireless Switch and Plug-in

1 Answer

Flood light has faint glow at all time

Just replaced a non-motion sensitive flood light with a sensitive flood light. I am noticing that the there is a faint glow at all times come from the flood light bulb. Why?

Posted by on

  • blarson12 Apr 27, 2009

    I installed 2 motion sensor lights on my son's garage, the 4182's I believe. Anyway, during the daylight hours you can still see the center

    filament in the light bulb is glowing orange.

  • trgaultney
    trgaultney Nov 07, 2012

    my sh 5105 stays on dim day and night, when i walk in front of it will go to bright, will stay bright for i min and go back to dim.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Sounds like you have the Dual Brite on, the dual brite is low level accent lighting. Check to see if you have this switched on, if so turn it off.

Posted on Apr 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get the light to turn on and stay on?


I checked a similar Regent device and its instructions refer to using TEST mode. If you have any non-automatic mode, try using that. There may be a time out provision that turns the lights off after a certain "on" period.

Jul 25, 2015 | Defiant Flood Lights. 180 Degree Outdoor...

1 Answer

I have set all the switches to the left TEST, Low sensitivity and Dual brite OFF and this light stays on all night??


putting the switches on test bypasses all the sensors leaving the light on all the time the test selection is only there to see if the light is working

Jan 15, 2015 | Defiant Flood Lights. 180 Degree Outdoor...

1 Answer

Maytag dg313 series 7 dryer will not light


Thermocouple. The igniter heats the thermocouple to turn on the gas valve and fire the burner.

Nov 29, 2013 | Dryers

1 Answer

Flood lights in back yard not working


Which kind of flood lights? Long time lighting during whole night or security lighting sensitive to people walking across.

If it is for long time lighting, you should select the fixture lighting source as compact fluorescent, led or small wattage HID lamps, this kind of fixture you do not have priority requirement for instant on, the following fixture is just for reference.

http://www.bulbspro.com/vista-10040-35w-hps-wall-fixture-w-photoelectric-eye-bronze.html

For security purpose, you need the flood light right away reach full brightness, normally you take following fixture with halogen bulbs.

http://www.bulbspro.com/vista-10031-motion-sensor-twin-light-control-kit-white.html

Good luck!

Nov 10, 2013 | Dishwashers

1 Answer

Motion light stays on


If there is a "sensitivity" setting, it appears to be sett too sensitive, therefore the unit thinks there is constant motion.

Feb 23, 2013 | Cooper Lighting regent light BRZ Motion...

1 Answer

Why do my lights stay on during the day how do i reset them


What sort of lights?

Are they the "motion-detector" outdoor flood-lights?
If so, adjust the "sensitivity" dials on the unit.

Oct 23, 2010 | Computers & Internet

1 Answer

We can't get the motion on our flood lights to work, what are we doing wrong?our flood lights will go on with the light switch; however, they remain on all the time and will only go off when turned off.


There are different selections on a flood light that you have to adjust. It is possible the you have it in test mode right now and when you flip the switch you are sending powering to the flood and it will stay on because it is in test mode. If it is not in test mode and you have it in the normal operation mode you may have the sensitivity set to high. If there are bushes near, running water, or anything that is moving quite a bit all the time it's going to stay on. Also, depending upon how old the flood is. It may simply need replacing. I would check the first two items and go from there. If you become completely stumped, a good electrician should be able to problem solve this very quickly. I have been on a few service calls where simply the flood was bad and needed to be replaced. I hope this helps.

Jul 12, 2009 | Camping, Backpacking & Hiking

2 Answers

2003 honda element,with a fully charged battery the car will start fine up to 1 week after that it will not start,that with the car setting idle,there are no lights,radio,or any other battery drains that...


HI, i would try to isolate this drain. once isolated, it will be easier to repair.

Here is the procedure I use to isolate a battery drain. Remove negative battery cable from the battery. Using a 12-volt test light, hook one end to the negative battery post the other end to the negative battery cable you just disconnected. The test light will glow or "light" if there is a drain. If the "light or glow" is faint, that is probably normal draw for the clock or computer. If the "light or glow" is bright, then there is a large drain. That should be corrected. Now start removing and replacing the fuses one by one until the light goes out; that one will be the circuit with the drain. Remember to hold in the button in the door jam for the interior lights.

May 03, 2009 | 2003 Honda Element

1 Answer

Eerie Orange/Red Glow Inside Floodlights (bulbs)


I think this is by design. Look at the instruction manual and it should tell you. This doesn't make sense that they should be on, but they may have a reason for it in their design. Now to the bulb saver technology thought, you are mostly right here. There is a lot of "strain" if you will on the filament when starting it up and it does cause a weakening over time. You will notice that when a bulb goes out, it usually happens right when you turn it on. The same thought here. I suppose in this device, that a constant voltage (low) is better and more efficient than zero voltage to 120 volts. They probably take into account the sensor will be used several times a day thus making the need for this kind of set up even more demanding.

Mar 02, 2009 | Electrical Supplies

Not finding what you are looking for?
Heath Zenith SL-6136-WH Basic Solutions Wireless Switch and Plug-in Logo

Related Topics:

453 people viewed this question

Ask a Question

Usually answered in minutes!

Top Heath Zenith Electrical Supplies Experts

Steve

Level 3 Expert

3287 Answers

ken skalski

Level 2 Expert

150 Answers

Gene Haynes

Level 3 Expert

5080 Answers

Are you a Heath Zenith Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...