Question about Denon AVR-483 5.1 Channels Receiver

1 Answer

Won't stay on

The device was playing normaly and after an hour it turned offsce the when ever i try to turned it on , it beginsto show everything in the display normaly but always shuts down after 5 to 6 seconds .

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 145 Answers

This is normally caused when the overload protection circuit kicks in. To see if this is the case, unplug everything (except power) including speakers and then power on th receiver. If it stays on then try reconnecting speakers one by one. If one of the speakers causes the failure then follow the speaker wire back to the speaker and examine for damage. If all speakers work then start adding components back one by one and test as each one is re-connected.

good luck

Posted on Mar 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Setup help for record player (Pro-Ject Carbon Debut) and pre-amp (ART DJPRE II) into Denon AVR-1909. I have everything setup properly, but I cannot get the subwoofer to turn on with my 2-channel settings...


In two channel mode, there will be no subwoofer signal unless you change the front speakers to 'small'. If you set the front speakers as 'large' then the full frequency spectrum will be sent to the front speakers, and none to the sub. Switching from bluray may keep the surround configuration until you restart as you mentioned.

Sep 26, 2013 | Denon AVR-1909 Receiver

1 Answer

Bose wave radio cd won't play cd's


If your CD is not scratched,the optical lens need replacement.

Apr 02, 2013 | Bose Awrc1g Wave Radio Cd Player Only -...

1 Answer

My sony dvd player won't turn on


Almost all devices might go through something like this. Sometimes, its the cable that get broken or loose. When I say loose, i mean to say that some cables have to be moved to a special position, for example, the head phones I am using now, are placed in a special position because they're like 2 years old. Same thing happens with my play station 2. I have to keep moving the cable to make it work and turn on.

Mar 14, 2013 | Audio & Video Receivers

1 Answer

My Onkyo TX-SR506 plays cable and CD inputs to zone 2, but DVD won't play. Everything is connected according to the manual and I assigned zone 2 output correctly. What gives?


How are your cable and cd inputs hooked up? Analog connections? Alot of receivers cannot send an audio signal from hdmi inputs to zone 2.

Feb 06, 2013 | Onkyo TX-SR506 Receiver

1 Answer

My HTR 5460 won't stay on


try pressing power while holding the 'fm/am' and 'input mode' buttons. This will tell you what part of the circuit is making it shut down. It should show something like I PROTECT, PS PROTECT, etc.

Jan 10, 2013 | Yamaha Audio & Video Receivers

1 Answer

Receiver won't play music from an MP3 device


Use your computer speaker as the sound device or use a headphones.

If it sounds good, it could just be your cable that goes to the receiver.

( using a Y cable to connect to one of the regular audio inputs.)

or have one like these:

3.5MM To Stereo Rca Cables: Electronics

Sep 25, 2012 | Sony STRDH520

1 Answer

I just bought a used pontoon boat with a Clarion Marine M235 radio/cd player. The previous owner said there is a cd stuck in the player and won't eject or play. The display says "no cd" but I...


you have to open the unit cover to remove the CD, its probably tried to eject it and its past the point that shows one in the slot which is causing the player to say NO CD , once opened, use great care in moving anything, and keep track of where everything goes,

Jul 04, 2011 | Audio & Video Receivers

1 Answer

I have a fisher ca-9335 integrated stereo amplifier thats hooked up to sanyo tp 1010 turn table and plays out of yamaha ns-70t speakers. a simple jvc cd player is also hooked up to the speakers but not to...


Something doesn't add up. You mention two connections to the speakers - CA-9335 and a "simple jvc cd player". Is that true? If so, you might want to UNconnect the CD from the speakers and run it into the receiver where it belongs. An amp isn't designed to share the load with another live device; or even have electrical contact with anything BUT speakers.


Did you actually find documentation that supports this hook-up? Or just winging it?

Feb 20, 2011 | Audio & Video Receivers

4 Answers

Yamaha HTR-6130 Receiver will not stay on! Shuts


One last try with everything disconnected!
Other than that I suspect internal surge damage.

Aug 04, 2009 | Yamaha HTR-6130 Receiver

1 Answer

Reciever turning off.


You have a short in the speaker wiring. Simply put, the pos and neg (red/black ends) of your speaker wire are most likely touching somewhere. The receiver has a short protection circuit that keeps you from blowing the receiver or your speakers. Either try re-cutting the ends of the speaker wire, or if that doesn't remedy the issue, buy new speaker wire.

Jun 18, 2007 | Onkyo TX-SR601 Receiver

Not finding what you are looking for?
Denon AVR-483 5.1 Channels Receiver Logo

Related Topics:

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Denon Audio & Video Receivers Experts

 Elex
Elex

Level 2 Expert

49 Answers

jonpoint

Level 1 Expert

4 Answers

Tech Leprechaun
Tech Leprechaun

Level 2 Expert

61 Answers

Are you a Denon Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...